abo
Members-
Posts
240 -
Joined
-
Last visited
Profile Information
-
Gender
Male
-
Location
North East
Car Info
-
Model
Octavia 1.9 TDi 130 Ambiente SE
Recent Profile Visitors
abo's Achievements
-
What type of hub nut came with your new CV joint, and what torque procedure did you use to tighten it? I just had the same problem after changing a CV joint. The new one came with a hex nut, didn't realise they torqued differently to the standard 12 point nut, so I used the procedure in the Haynes manual and it pulled to the left horribly. I bought a replacement 12 point nut and now it's fine. You say it does it when not accelerating too so maybe something else, but this gotcha'd me so worth asking...
-
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Update: I decided to buy a couple of spare 12 point nuts, they arrived on Friday. Fitted one yesterday, torqued as per Haynes and it is *much* better. Still pulls a little under heavy throttle, I'm putting it down to either the nasty tyre on that side (will be replacing the fronts shortly) or possibly my torque wrench not being 100% -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
I assumed so when I bought it I've been using the place for 30 years and never had a problem (LT Motors in Stockton). Joint is a Shaftec CV351N which is suitable according to the compatability list here https://www.ebay.co.uk/itm/193465607960 -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Just googling some more... I followed the procedure in Haynes for tightening the hub nut which matches what I've read on the internet for the 12 point hub nut. People seem to be suggesting things are different for a hex nut which is what came with my new CV joint, but I cannot find consistent information for it, just a variety of torque numbers for the vehicle on and off the ground, and some Bentley procedure. Is this the case, if it is, then could this be the issue, and what is the correct procedure for torquing a hex hub nut? -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Hopefully not the case, the car was spot on before I did it (CV aside) -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Could be they got it wrong. Local company, literally just down the road from me. They've been there 40-odd years and I've used them for various reasons in the past but maybe not for an alignment. I lowered the car about five years ago and got it aligned at a different place (and they did a good job), I reckon I'll pop in there tomorrow and get a second opinion... -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Argh! Something is wrong somewhere, I took the car in for alignment just now and the problem is still there; still pulling left under throttle... It feels like there is only drive on one side, is it possible I've e.g. popped or otherwise shagged the inner CV when I've been messing about or something? -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Doh, of course it'll need tracking, I tinkered with the bottom arm ball joint... -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Definitely the CV joint. I've finally got round to replacing it and the noise has gone. I had to remove the whole driveshaft in the end and grind the CV joint to get to the circlip. I got the shaft out by undoing the steering arm ball joint and three bolts to the bottom arm, and knocking the hub off the CV joint. Then the six bolts on the other end. Slight problem now: the car pulls to the left under acceleration (the side with the dodgy CV). Everything screwed together ok, nuts and bolts are torqued to the settings as per Haynes. What could I have done wrong? -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Thanks, good to know! I'll have a look when it's not wet -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Does the CV joint rattle regardless of which direction I'm turning? This is only happening when I'm turning right. -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
I'll have a look at that when it isn't so wet, thanks. Exhaust is stainless, at least if that's the problem it has a lifetime guarantee iirc -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Can't reproduce it when the car is parked. I took it out just now and managed to record the noise it makes, you can hear it here, at about 7 seconds in when I pull out of a junction and again at about 18 seconds CV joint? -
Suspension (?) noise, need help to identify it
abo replied to abo's topic in Skoda Octavia Mk I (1996-2004)
Hmm, not so much a cracking, it sounds more creaky. I'll see if I can get a recording of it, not sure how well it'll pick up though. -
I'm hoping someone can point me in the right direction please? My Octavia is making an unfamiliar noise from the front passenger corner, but only when I am turning right and have some throttle. If I eg coast around the corner or roundabout then it doesn't make the noise. The noise is a little hard for me to describe, it sounds like it is creaky. Not like a spring, and it isn't a grinding/knocking/rattling. I'm thinking strut top mount? But I'm not familiar with the symptoms or noises this may cause so wanted to get some advice before just trying to dive in...