danikd
Finding my way-
Posts
16 -
Joined
-
Last visited
Profile Information
-
Location
Czech Republic
Car Info
-
Model
Citigo
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
danikd's Achievements
-
Hi, after years, anyone, any updates, same error on my car ... Thx for info. DAniel
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
And you must slide main cover of connector and separate two sliding halves to access all inner line of connectors :) I added about 15-20 wires to BCM :) in my retrofits ... one word - horror ... good led light, small fingers, BCM out ( its easy - 20secs ) and each connector to left side (LHD) and you will see it in the gap near pedals ... one hand holding, second working ... hard to describe, you must try it... Or you can remove whole dashboard and there is easy acces to connector- 44 replies
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
Hello, to retrofit MFSW you need facelift BCM with pin 17 ( no prefacelift with it ). But every facelift need new wiring to clocks ... No wires, no communication with BCM - non running car ... its easy ... 3digit letter code is addictional code - no need for it, its for ordering corfigurations ( coding, adaptations ) - everything can be manualy edited ... Anyway, the code isnt on BCM label, so you cant choose on used unit ... BCM of same version should have same HW and SW revision ... so all must have same pinout - so pin 17 must be there ... but check it via photo, for sure And pin T73b/17 its easy to find, see my picture above ... Finally, you can choose from e-up!/up!/Citigo/Mii, Polo 6R, Rapid, T5/T6, BCMs ... Personally I have T5/T6 7E0 937 090 C - Which is MAX BCM ( support almost everything ) without single error in VCDS ... BUT be aware from units with 315MHz remote freq. ... ( for example 7E0 937 190 C ) U need 434Mhz remote freq, which is use in Europe ( check your freq - lasered under blade of remote control ) Regards Dan- 44 replies
-
- 1
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
Make 2 new ones, on present canbus wiring harness, there are more units attached in the way of harness ... T73b/17 in 2012 is described as unnasigned because MFSW is in MY17+ ... and before there was no BCM with this pin- 44 replies
-
- 1
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
Its easy, but new BCM need new connection ... always check wiring diagram before!- 44 replies
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
New BCMs from facelift Citigo use different canbus for instrument cluster- new CAN-COMBI ( sorry prev., post was mistake CAN-INST ) than old BCMs ... You must make 2 new wires : 1)pin 29 on instrument cluster to pin 57 White connector B on BCM 2)pin 28 on instrument cluster to pin 54 White connector B on BCM Old BCM has instr. cluster on motor CAN, pins 18 and 19 on BCMs side ... Than your new BCM will be OK with instr. cluster. Than you make wire from T73b/17 - LIN bus to stalk connector, +12V also there, as in wiring scheme - you have new small connenctor, I have old big ( car without start/stop ) And you need new airbag cable for MFSW Thats all for MFSW ...- 44 replies
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
You need to change BCM ... T73b/17 is needed ... F unit will be ok, but before you buy, always find desired unit on google pictures, same HW and SW and chceck pin present ... Finally I have MAX unit from Polo/T5/e-up, which support heated windscreen which I have. So its good to thing about your retrofits and make BCM wiring in one shot, because is not fun to mange pins in bcm connector, there is no space :( And if you change BCM for FL, which F is, chech wiring diagram, there is different cluster panel CAN conenction, new has special, CAN-INST wiring ... so another two wires to BCM- 44 replies
-
- 1
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
Autostart? Details pls ... Fog lights i had, only modded wiring to support corner ( I have old 2013 ), modded-retrofitted OEM autolights ( thx Ciclo : https://uk-polos.net/viewtopic.php?t=71456&start=45 ), rain/light sensor, Citisafe sensor, heated windshield, FL headlights with LED, spoilers, 7E0 MAX BCM, FL cluster with maxidot, MFSW, TMPS ... many things Now working on : Heated seats wiring ( seats later, maybe leather ), Beats soundsystem retrofit, MIB2 Amundsen retrofit with new climapanel and OEM rear camera, folding mirrors with dynamic turn signal and puddle lights, footwell lights, comfort windows with rainclose, black MC interior, new green/black logos ... Ask what you want- 44 replies
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Thx for info, unit will be soon, but I must resolve how to fit this 2DIN unit to CItigo ... Iam working on custom panel ...
-
Multifunction steering wheel adding one to pre-face lift model
danikd replied to P3P5I's topic in Škoda Citigo
Hi there, sorry I havent notifications for this post. I can help, what do you guys need ... which BCM support MFSW?- 44 replies
-
- citigo
- multifunction
-
(and 1 more)
Tagged with:
-
Any one who has it, in VCDS, there are some errors? Somewhere I find that there are some errors, not registered or something liake that ... its due can filter for PQ cars? many thx for info. Daniel
-
pab567, cant send you PM, dont know why. Can you help me with crazy project - 2 DIN MIB2 in Citigo? Pls let me know ...
-
One questions, MFSW buttons are iluminated or not? Thx for info. Dan
-
David, great work with your CG. Octa Mk3 MFSW is fully working? The buttons ... OR only volume and prev/next? What I need to retrofit it - MFSW + MFSW cable and ??? Thx for info. Daniel