Guide : How to fit Leon front splitter

Phill JK · 15-01-2006, 19:03

Fitting the Seat Leon front splitter is quite easy but the part needs cutting in places to fit.

First you will need a mate to help as someone needs to hold the splitter in place while you mark where it fits. A cutting tool and 14 self tapping screws will be needed. Part number is for the splitter is 1ML 805 903

I decided to fit the splitter so it went smoothly around the very edge of the bumper;

The part needs to bend slightly so to stop it from deforming and giving a crease I cut 2 small triangles so that it bends easier;

Next smooth off the top of the 2 lugs in the centre of the splitter - 2mm above the plasic bit that is in them so you can screw them in later on;

Then use some masking tape (and your mate!) to line up the splitter;

Ensure you tape it on so you can stand back and ensure its even.

Then drill through the small clips on the splitter into the spoiler - they have a small edge on them so best to file these down first so they are smooth. Screw into the bumper all around the edge;

You will need to cut about 3cm off each edge so it sits in front of the mudflap.
Finally you'll need to small headed screws (I had to grind some down to fit), screw in the 2 lugs to the bumper. I also used some black stickyflex to help adhesion;

Stand back and admire

Mike VRS · 15-01-2006, 21:30

Great Guide, you dont by chance have any front on pictures of the finished look in red?

Phill JK · 15-01-2006, 21:57

Thanks

I did take some pics of the front but the flash mustn't have worked, I'll get some up this week

eatsoot04 · 15-01-2006, 23:50

Great guide mate.

Couple of quick Q's

*did you use any other adhesion apart from screws?
*where the screws self tapping?
*What are self tapping screws (sits in ignorant corner)
*and finally did you drill any holes in the skoda bumper first for the screws or just screw em in?

Sorry for the ignoramus questions just wanna make sure its correct.

Thanks

Alex the stupid. ;-D

landwomble · 15-01-2006, 23:53

looking good, bring it round so i can have a look...you reckoned it might fit a superb as well....!

bananaman · 15-01-2006, 23:55

got ne frontal pics m8*

Mike VRS · 16-01-2006, 01:42

Quote:

Originally Posted by eatsoot04

*What are self tapping screws (sits in ignorant corner)
*and finally did you drill any holes in the skoda bumper first for the screws or just screw em in?

Self tapping screws are screws with a head on them a bit like the tip of a drill bit, Therefore you dont need to drill a hole toscrew them in, as you start to screw the 'drillbit head' digs into the material and forces the screw through the material.
They are available in any DIY store and make it alot easier than predrilling holes for normal screws etc

daver · 16-01-2006, 08:58

I wonder what this would look like on an Ocy vRS, might not last long though its alreadt very low as standard......and mines not quite standard!

vrsfab · 16-01-2006, 09:10

See here for pictures of splitter on a black Fabia:-

http://www.briskoda.net/forums/fabia...-bumper-8.html

Phill JK · 16-01-2006, 09:21

Quote:

Originally Posted by eatsoot04

*did you use any other adhesion apart from screws?
*where the screws self tapping?
*What are self tapping screws (sits in ignorant corner)
*and finally did you drill any holes in the skoda bumper first for the screws or just screw em in?

Thanks guys

I used screws all the way around just straight into the bumper (but did drill a much thinner hole first just to help the screw), but used this silicone type glue under the 2 centre lugs to stick them before screwing them in as its difficult to enter a screw accurately into them as they are so thin.
Think its called stickyflex and comes in black, you can see it on the picture. You could get away without this but mine had about a 1mm gap at the top of the lugs so just used it to fill them in.

Phill JK · 16-01-2006, 09:25

Quote:

Originally Posted by landwomble

looking good, bring it round so i can have a look...you reckoned it might fit a superb as well....!

Will do mate! Cant see it fitting yours now, it would be missing about a foot of plastic in the middle!!

landwomble · 16-01-2006, 18:01

i reckon i could fit your whole car in my boot!

Phill JK · 16-01-2006, 20:38

Quote:

Originally Posted by landwomble

i reckon i could fit your whole car in my boot!

You could fit half of Wales in your boot!

Phill JK · 17-01-2006, 12:25

Probably should have posted this in the guides section.. anyone know how I should move it?

HellFire · 17-01-2006, 12:37

Can we get some front pics of the car with the splitter? it'd be nice to see how it looks on a Red vRS, hopefully when I fit mine (now I have the info should be this weekend) I will create an album of what it looks like on all the vRS's.

Could everyone please take some pics then i'll create a post (mods if you could make it sticky) so everyone can see what it looks like on different colours?

Phill JK · 17-01-2006, 12:42

Quote:

Originally Posted by HellFire

Can we get some front pics of the car with the splitter? it'd be nice to see how it looks on a Red vRS, hopefully when I fit mine (now I have the info should be this weekend) I will create an album of what it looks like on all the vRS's.

Could everyone please take some pics then i'll create a post (mods if you could make it sticky) so everyone can see what it looks like on different colours?

Took some front pics this morning before I came to work - i'll get them up tonight

HellFire · 17-01-2006, 13:58

excellent. i hope everyone agrees this will be useful as I have a feeling this will become mod of the year 2006.

vindaloo · 17-01-2006, 18:35

I may be in a minority here...

I don't like the way the centre part of the splitter appears in comparison to the Styling of the Skoda front bumper. The radiator apperture doesn't line up. The centre bar on the splitter needs to be wider to match the front bumper.

I think it can be made to work but I also think that it may end up being a lot of work unless you cut the centre chunk out and use the remaining two pieces as lip corners.

Think I'll have a play with some images.

eatsoot04 · 17-01-2006, 22:10

vindaloo know what your saying.

I agree but i just tell peple to look from an angle. lol

HellFire · 18-01-2006, 10:38

I like it, guess i'll have to see what it's like once fitted.

So far I have some good pics of a black vrs and a red vrs.

just need a yellow & silver now (silver one on the way curtosy of me

).

vindaloo · 18-01-2006, 13:51

Quote:

Originally Posted by eatsoot04

vindaloo know what your saying.

I agree but i just tell peple to look from an angle. lol

I s'pose anyone with the same POV as the camera would have more on their mind than just, "tut the styling quite odd" as they'd have just been knocked over.

It definitely needs work rather than just bolting on though. I think losing the center bar would give it an edginess if the sides bits are tailored to the apperture. A bit F360ish without being obvious.

As an aside, I went looking for splitters on the internet last night <thud>. Have you seen the prices!?

Add the initials DTM to a piece of formica and it's £100+.

Think I'd rather spend £20 and take it plus a bit of A4 with my thought to a local fabricator/bodyshop.

J.

HellFire · 18-01-2006, 16:58

sorry but i think i was in the wrong state of mind or blind.

which bit doesn't look right?

any pics or the suspect part?

vindaloo · 18-01-2006, 18:27

Piccie 2 of the black one.

http://www.briskoda.net/forums/fabia...-bumper-8.html

J.

Phill JK · 18-01-2006, 18:47

Bear in mind that people dont see it from that low down.

Had mine on for a few days now and had nothing but positive comments

My fav (and cheapest!) mod so far.

Akebono · 19-01-2006, 13:01

no silver one yet?

I would do mine, but it's not RS, so too much variables in the equation ...

15-01-2006, 19:03	#1
Phill JK Briskodian Join Date: Apr 2004 Posts: 242 Thanks: 0 Thanked 0 Times in 0 Posts	Guide : How to fit Leon front splitter Fitting the Seat Leon front splitter is quite easy but the part needs cutting in places to fit. First you will need a mate to help as someone needs to hold the splitter in place while you mark where it fits. A cutting tool and 14 self tapping screws will be needed. Part number is for the splitter is 1ML 805 903 I decided to fit the splitter so it went smoothly around the very edge of the bumper; The part needs to bend slightly so to stop it from deforming and giving a crease I cut 2 small triangles so that it bends easier; Next smooth off the top of the 2 lugs in the centre of the splitter - 2mm above the plasic bit that is in them so you can screw them in later on; Then use some masking tape (and your mate!) to line up the splitter; Ensure you tape it on so you can stand back and ensure its even. Then drill through the small clips on the splitter into the spoiler - they have a small edge on them so best to file these down first so they are smooth. Screw into the bumper all around the edge; You will need to cut about 3cm off each edge so it sits in front of the mudflap. Finally you'll need to small headed screws (I had to grind some down to fit), screw in the 2 lugs to the bumper. I also used some black stickyflex to help adhesion; Stand back and admire Last edited by Phill JK; 21-01-2006 at 19:04.

15-01-2006, 21:30	#2
Mike VRS Briskodian Join Date: Jan 2006 Location: Belfast, N. Ireland Posts: 120 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Guide : How to fit Leon front splitter Great Guide, you dont by chance have any front on pictures of the finished look in red? __________________ 06 Fabia VRS in Shiney Silver Mapped by O.B.D. AutoTune 03 Honda S2000 GT Spec + 05 Brabus Fortwo In Czech, the word 'škoda' means "damage, detriment, disadvantage", and "To je škoda" meaning "It's a pity"

15-01-2006, 21:57	#3
Phill JK Briskodian Join Date: Apr 2004 Posts: 242 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Guide : How to fit Leon front splitter Thanks I did take some pics of the front but the flash mustn't have worked, I'll get some up this week

15-01-2006, 23:50	#4
eatsoot04 Briskodian Join Date: Dec 2004 Location: nr Manchester Posts: 835 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Guide : How to fit Leon front splitter Great guide mate. Couple of quick Q's did you use any other adhesion apart from screws? where the screws self tapping? What are self tapping screws (sits in ignorant corner) and finally did you drill any holes in the skoda bumper first for the screws or just screw em in? Sorry for the ignoramus questions just wanna make sure its correct. Thanks Alex the stupid. ;-D __________________ Alex Revo Chilly Alpine ICE Cupra Intake Green Cotton Filter RS6 wheels 184 BHP

15-01-2006, 23:53	#5
landwomble Briskodian Join Date: Mar 2005 Location: North West UK Posts: 459 Thanks: 0 Thanked 0 Times in 0 Posts	Re: Guide : How to fit Leon front splitter looking good, bring it round so i can have a look...you reckoned it might fit a superb as well....!