Jump to content

O3 FL High Beam Assist - VCDS Autoscan


Recommended Posts

Does anyone with an Octavia 3 Facelift MY18 vehicle have High Beam Assist specced from the factory? If so, and you've got or could get access to VCDS, would you be able to do an autoscan and adaptation channel map? I'm trying to enable HBA on my Scout, but the long coding is not editable as yet, it's just zeros.

Link to comment
Share on other sites

2 minutes ago, langers2k said:

@wg100, it might be worth posting an autoscan for your vehicle too :)

 

I should have thought of that when I saw @andyvee this afternoon. Am thinking of getting VCDS for myself, so may be able to do so soon.

Link to comment
Share on other sites

I don't think the coding is masked, instead it looks like VAG might be changing from lcode to adaption channels - at least based on this thread: http://forums.ross-tech.com/showthread.php?10616-Modules-reporting-zero-code-string

 

Andy, did you get an adaption map for 09? Might be worth posting it up on rosstechs forum as there are few people on there that might be able to help :)

  • Like 1
Link to comment
Share on other sites

No I didn't, the laptop battery wouldn't have lasted the half hour or so it takes to pull the adaptation map from 09!

 

Interesting though, this is the first FL O3 I have seen so haven't got anything to compare it with :(

 

I might try scanning my own Kodiaq and seeing how that is set up - I haven't had time!

Link to comment
Share on other sites

I have an admap of my 1.5 SE L TSi DSG taken the day after delivery to me so it's fresh from the factory. I also  have autoscan which shows a couple of faults found.

 

Please PM me if you would like a copy.

Edited by YMe
Making sense.
  • Like 1
Link to comment
Share on other sites

35 minutes ago, YMe said:

I have an admap of my 1.5 SE L TSi DSG taken the day after delivery to me so it's fresh from the factory. I also  have autoscan which shows a couple of faults found.

 

Please PM me if you would like a copy.

Did you have high beam assist from the factory?

Link to comment
Share on other sites

These channels are interesting in YMe's map (with HBA):

ENG141650-MAS13782-Fernlicht_assistent-Will Beam assistant: responsivity adjustable via BAP    present
ENG141650-ENG141973-Fernlicht_assistent-Erweiterte_Fernlichtsteuerung    AFS: FLA: Fernlicht ueber AFS
ENG141650-ENG116639-Fernlicht_assistent-Fernlichtassistent Reset    active
ENG141650-ENG116637-Fernlicht_assistent-Menuesteuerung Fernlichtassistent    present
ENG141650-ENG116641-Fernlicht_assistent-Menuesteuerung Fernlichtassistent Werkseinstellung    present

 

This is from another O3 FL (probably with no HBA):

ENG141650-MAS13782-Fernlicht_assistent-Will Beam assistant: responsivity adjustable via BAP    present
ENG141650-ENG141973-Fernlicht_assistent-Erweiterte_Fernlichtsteuerung    AFS: Fernlicht ueber AFS
ENG141650-ENG116639-Fernlicht_assistent-Fernlichtassistent Reset    active
ENG141650-ENG116637-Fernlicht_assistent-Menuesteuerung Fernlichtassistent    Not Present
ENG141650-ENG116641-Fernlicht_assistent-Menuesteuerung Fernlichtassistent Werkseinstellung    Not Present

 

I would change the 3 red marked channels for a start. Probably the camera module still needs coding afterwards.

It seems that these are new channels in the FL.

Edited by aki78
  • Like 1
Link to comment
Share on other sites

Dito :

 Address 09: Cent. Elect. (J519)       Labels:. 5Q0-937-08X-V2.clb
   Part No SW: 5Q0 937 084 CG    HW: 5Q0 937 084 CG
   Component: BCM MQBAB H   H34 0236  
   Serial number: 02001709503163
   Coding: 000000000000000000000000000000000000000000000000000000000000
   Shop #: WSC 73430 790 00000
   ASAM Dataset: EV_BCMMQB 017001
   ROD: EV_BCMBOSCH_017.rod
   VCID: 7F077CDAE63159D2C53-802A

Link to comment
Share on other sites

Doh - just read the thread properly and checked out that Ross-Tech Forum Thread - that would explain why my coding is all Zeros. So time to do an Adaption Log to see what settings I have before playing.

On 11/11/2017 at 21:40, langers2k said:

I don't think the coding is masked, instead it looks like VAG might be changing from lcode to adaption channels - at least based on this thread: http://forums.ross-tech.com/showthread.php?10616-Modules-reporting-zero-code-string

 

Andy, did you get an adaption map for 09? Might be worth posting it up on rosstechs forum as there are few people on there that might be able to help :)

 

29 minutes ago, Gti Jazz Blue said:

Dito :

 Address 09: Cent. Elect. (J519)       Labels:. 5Q0-937-08X-V2.clb
   Part No SW: 5Q0 937 084 CG    HW: 5Q0 937 084 CG
   Component: BCM MQBAB H   H34 0236  
   Serial number: 02001709503163
   Coding: 000000000000000000000000000000000000000000000000000000000000
   Shop #: WSC 73430 790 00000
   ASAM Dataset: EV_BCMMQB 017001
   ROD: EV_BCMBOSCH_017.rod
   VCID: 7F077CDAE63159D2C53-802A

 

Link to comment
Share on other sites

Oh joy - following the thread suggestion I sent an An Auto-Scan through for my May 2017 FL vRS and have just had this response back (with a thanks):

 

P.S. Your car has a few control modules (stuff like rear LED lighting modules) that are not able to communicate with your HEX+CAN interface so we would recommend trading it toward a HEX-NET using this page:

 

So it looks like it is upgrade time, the only thing that I don't like is the limited licence they introduced, I've help others out in the past and my cable has probably been through about 30 VINs, if I make the switch I'm going to have to be selfish and not assist anyone any more with a limit of 10 VINs - I'll need to keep them for myself / mates with Group Cars.

 

 

Link to comment
Share on other sites

2 minutes ago, Auric Goldfinger said:

 

Alright bezzie Mate...........:hi:

VCDS 3 VIN HEX-V2 cable ordered from Gendan, WiFi HEX is very nice but just more to go wrong at extra cost so I went for the USB version.

 

Went for an outright purchase so I can keep the current cable for unlimited use on older group cars - like my My Mum's Citygo and Daughters Altea.

Link to comment
Share on other sites

53 minutes ago, Gti Jazz Blue said:

VCDS 3 VIN HEX-V2 cable ordered from Gendan, WiFi HEX is very nice but just more to go wrong at extra cost so I went for the USB version.

 

Went for an outright purchase so I can keep the current cable for unlimited use on older group cars - like my My Mum's Citygo and Daughters Altea.

Am planning to get the Hex-V2 cable  when I'm back from my work trip in a couple of weeks. I'd be interested in hearing how you get on.

Link to comment
Share on other sites

  • 2 weeks later...
On 12/11/2017 at 18:31, aki78 said:

These channels are interesting in YMe's map (with HBA):

ENG141650-MAS13782-Fernlicht_assistent-Will Beam assistant: responsivity adjustable via BAP    present
ENG141650-ENG141973-Fernlicht_assistent-Erweiterte_Fernlichtsteuerung    AFS: FLA: Fernlicht ueber AFS
ENG141650-ENG116639-Fernlicht_assistent-Fernlichtassistent Reset    active
ENG141650-ENG116637-Fernlicht_assistent-Menuesteuerung Fernlichtassistent    present
ENG141650-ENG116641-Fernlicht_assistent-Menuesteuerung Fernlichtassistent Werkseinstellung    present

 

This is from another O3 FL (probably with no HBA):

ENG141650-MAS13782-Fernlicht_assistent-Will Beam assistant: responsivity adjustable via BAP    present
ENG141650-ENG141973-Fernlicht_assistent-Erweiterte_Fernlichtsteuerung    AFS: Fernlicht ueber AFS
ENG141650-ENG116639-Fernlicht_assistent-Fernlichtassistent Reset    active
ENG141650-ENG116637-Fernlicht_assistent-Menuesteuerung Fernlichtassistent    Not Present
ENG141650-ENG116641-Fernlicht_assistent-Menuesteuerung Fernlichtassistent Werkseinstellung    Not Present

 

I would change the 3 red marked channels for a start. Probably the camera module still needs coding afterwards.

It seems that these are new channels in the FL.

 

Changing the highlighted channels has enable the light assist option in the light settings, however "fault: light assist" appears on the MFD when the high beam is engaged, so there is still some coding to be done.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Community Partner

×
×
  • Create New...

Important Information

Welcome to BRISKODA. Please note the following important links Terms of Use. We have a comprehensive Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.