drbig

Do you really think it could be the cam sensor again ?

High Pressure Fuel Pump

Any thoughts 2010 yeti 4x4 with the 170 2.0 engine with over 200K on the clock. Recently had a replacement HPFP and cam sensor plus cam belt and water pump. But today just wont start on the key. Can turn the car over and over and wont start. A quick squirt of easy start in the air intake and the car will start and tick over. Turn it off and wont start. Faults logged Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1 Part No SW: 5L0 920 940 E HW: 5L0 920 940 E Component: KOMBI H08 0305 Serial number: 00000000000000 Coding: 720D00 Shop #: WSC 62021 220 97033 ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04052 ROD: EV_Kombi_UDS_VDD_RM09_004_SK34.rod VCID: 2E57F09C71F3363A7F-807A 1 Fault Found: 9453074 - Fuel Level Sensor 1 B103E 1B [008] - Resistance Too High Intermittent - Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 2 Reset counter: 226 ------------------------------------------------------------------------------- Address 19: CAN Gateway Labels:. 1K0-907-530-V4.clb Part No SW: 1K0 907 530 AD HW: 1K0 907 951 Component: J533 Gateway H16 0233 Revision: H16 Serial number: 4520K102030132 Coding: E9A37F06500602006303 Shop #: WSC 33361 790 00999 VCID: 69DD4380409D91026A-803C 1 Fault Found: 00470 - Company Comfort Databus in Single Wire 011 - Open Circuit Freeze Frame: Fault Status: 01101011 Fault Priority: 3 Fault Frequency: 254 Reset counter: 187 Mileage: 327368 km Time Indication: 0

If its still for sale ill take it

http://www.ebay.co.uk/itm/Mercedes-E320-Cdi/230997858684

For those that have the roof bars for your Yeti this may be of interest I have been looking for a bag to Store the bars in when not on the Yeti and found this from Audi Audi part number 8R0071156C The roof bars fit perfectly and the bag is very well made.

I had the same problem but a few months back when washing the car the strip lifted on one end Also if you have the silver strips on the front they are likely to fall off as they are stuck in a similar fashion

No problem

Here are some other pictures that I took before fitting Drivers Side Fitting is simple as TJK said you just need to muster up the courage to tug hard to remove the existing one Fitting just needs a very firm press to fit

Few More Pictures Here

Think they all are I done it many times with various makes of car.

The Kenwood looks interesting as it supports IPOD connect Bit more info here More info HERE @ the Kenwood Site

Fabia Hatch and Estate 2010 > and Roomster 2010 and the other Fabia Hatch and Estate 2010 > and Roomster 2010

Listed HERE

No mine is strapped to the bottom of the top tray There is a sort of fin on the unit from what I can tell the mounting point is some place behind the heater control.

I would not leave it like that it's ok for testing Funny though it did not rattle or give any problems

You should be able to mount the unit easily where you like as there is plenty of room in and around the console area

also the Ebay link is showing the part number as 5N0035341C of the MDI Part number listed in ETKA is 5N0 035 342B to correct this 5N0 035 342 B - MDI - to 30.05.2010 5N0 035 342 C - MDI - From 31.05.2010 Also listed is 5L0 971 199 - Adapter wiring set - This attaches to the MDI So the part number on ebay should work if you have a later build

That part contains the MDI unit that is mounted in an arm rest adaptor for a VW it wont fit a Yeti But you can remove the MDI from the arm rest adaptor to use

Take it you don't like it then

Pull up the gear leaver cover and trim ... You will then see the fixings holding the tray in place

I have not found a UK one only the left hand drive version and I have the left hand drive version of the tray and it wont fit right hand drive car

I can help you drop me a PM and will sort something out

Would have thought the tray was held in the same as the pocket a couple of torx near the front.