Divak

thanks you sir, let me trace and update sir. thanks and have a great weekend.

hi All good morning and hope all should be doing great. while i am waiting for some expert advise from you i continued my investigation and following is my observation. this metering device N290 is normally open solenoid valve and if you give the signal, the valve closes. so if i remove the signal connectors the valve is in open condition and allows more fuel to the rail and VCDS reports fuel high pressure and shuts the car. if i connect the supply connectors back to this valve the valve closes and no fuel to rail and car is not starting. short story short, i yet to trace the cable from the valve to the fuse holders but i checked all the fuses. all i need how will the ECM controls this valve, technically the ECM closes the valve when the fuel pressure is high and more fuel comes and so on. i think it take the input from G247 fuel pressure sensor on the distributor and also the fuel pressure regulator N276 which builds and release the pressure as needed. I checked the return fuel pip for clogging and its free. but engine module in VCDS is not reporting any error other than the coolant temperature is very high if i connect the coolant temperature sensor in the radiator outlet G83 and in the coolant inlet connects to the block G62 and because of this the temperature sensor reading in the dashboard insert is showing extreme red. I yet to check the Oil level and oil temperature sender - G266 under the engine block cover and yet to trace these cables back to fuse tray for any rat bites. is there any other technical advise please help me. i am trying to fix this over this weekend please help. appreciate all your help in advance

Dear All - hope all should be having great weekends. problem statement is my car is not starting. it had flat battery and was standing for a while on flat battery. I recharged them and connected it back and the car started fine, it was running fine for 15 minutes and then stopped and from then never starts again. i checked the following 1. battery terminal voltage - 12.5 and above and good 2. compression test on cylinder - all ok as per factory manual 3. fuel from tank pressure and flow is ok 4. fuel delivery from electric pump to HPP is good and pressure is perfect as per factory manual so i suspected the HPP and removed the delivery line of HPP that goes to injection units distribution and found no fuel coming. i though it could be HPP issue and traced all the fuses, cables relays etc both in cabin, in engine comportment, all perfect. however the HPP is not sending fuel. so i removed the N290 fuel dosing (metering device) from the HPP to check the signals, and cranked the car without the metering device connected to HPP, the car started running fine. it run for quite a while and stopped after some time saying the fuel pressure is too high in VCDS. also the vcds is reporting the N290 valve is open circuit because it was not connected. if i connect it back to HPP and the car is not at all starting, it cranks well and the VCDS is not reporting any error in the engine module. below is my scan report. is there any expert advice that i you share to check ? how do i check the metering device whether this is faulty? i do not want to buy a new one to replace them before confirming thats the issue. its very expensive here in India and please help. below is my vcds scan report. below is the latest scan report how do i get the freeze frame data using the VCDS? Saturday,25,September,2021,16:49:53:29955 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 21.9.0.2 (x64) HEX-V2 CB: 0.4555.4 Data version: 20210903 DS330.0 www.Ross-Tech.com VIN: TMBBNC1Z9AA151374 License Plate: Chassis Type: 1Z-SK35 (1K0) Scan: 01 03 08 09 10 15 16 17 19 25 42 44 46 52 56 62 72 VIN: TMBBNC1Z9AA151374 Mileage: 116440km-72352miles 01-Engine -- Status: OK 0000 03-ABS Brakes -- Status: OK 0000 04-Steering Angle -- Status: OK 0000 08-Auto HVAC -- Status: OK 0000 09-Cent. Elect. -- Status: OK 0000 10-Park/Steer Assist -- Status: OK 0000 15-Airbags -- Status: OK 0000 16-Steering wheel -- Status: OK 0000 17-Instruments -- Status: OK 0000 19-CAN Gateway -- Status: OK 0000 25-Immobilizer -- Status: OK 0000 42-Door Elect, Driver -- Status: Malfunction 0010 44-Steering Assist -- Status: Malfunction 0010 46-Central Conv. -- Status: OK 0000 52-Door Elect, Pass. -- Status: OK 0000 56-Radio -- Status: OK 0000 62-Door, Rear Left -- Status: OK 0000 72-Door, Rear Right -- Status: OK 0000 ------------------------------------------------------------------------------- Address 01: Engine (J623-CLCA) Labels:. 03L-906-018-CFF.clb Part No SW: 03L 906 018 EJ HW: 03L 906 018 BR Component: R4 2.0l TDI H20 9977 Revision: 42H20--- Serial number: CVN: BA7A8368 Coding: 00110012040500080000 Shop #: WSC 10259 663 00000 ASAM Dataset: EV_ECM20TDI01103L906018EJ 003008 ROD: EV_ECM20TDI01103L906018EJ.rod VCID: 76B5E25848406D8B8DD-8022 VINID: 91D49279306A2514411410C710D22E088E No fault code found. Readiness: 0 0 0 0 1 ------------------------------------------------------------------------------- Address 03: ABS Brakes Labels:. 1K0-907-379-MK70M.clb Part No SW: 1K0 907 379 AK HW: 1K0 907 379 AK Component: MK70 M MASR 0104 Revision: 00H35001 Coding: 0017665 Shop #: WSC 33361 790 00000 VCID: 7BA3F36C7FE230E3F23-802E No fault code found. ------------------------------------------------------------------------------- Address 08: Auto HVAC (J255) Labels:| 5K0-907-044.clb Part No SW: 3T0 907 044 AS HW: 3T0 907 044 AS Component: Climatronic H15 0401 Revision: 00005001 Coding: 0000001002 Shop #: WSC 73430 790 00000 ASAM Dataset: EV_Climatronic A01006 ROD: EV_ClimaAutoBasis_SK35.rod VCID: 03538B8C0B924823BA3-8056 No fault code found. ------------------------------------------------------------------------------- Address 09: Cent. Elect. (J519) Labels:. 1K0-937-08x-09.clb Part No SW: 1K0 937 087 D HW: 1K0 937 087 D Component: BCM PQ35 H 103 0575 Revision: 00103 AG Coding: 4E180AB8B00508C04008008011000124410000AE422085605C0440000000 Shop #: WSC 33361 790 00000 VCID: 323D1E48E42831AB615-8066 Subsystem 1 - Part No: 1Z2 955 119 C Labels: 1KX-955-119.CLB Component: Wischer 28011 22 0601 Coding: 00D7B7 Subsystem 2 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB Component: RLS 230110 05 54 0402 Coding: 0730ED No fault code found. ------------------------------------------------------------------------------- Address 10: Park/Steer Assist (J446) Labels:. 1Z0-919-475-V1.clb Part No SW: 1Z0 919 475 B HW: 1Z0 919 475 Component: PARKHILFE 4K H06 0006 Revision: -------- Serial number: 66641000904029 Coding: 100001 Shop #: WSC 33361 790 00000 VCID: 40D944805A84933BE71-8014 No fault code found. ------------------------------------------------------------------------------- Address 15: Airbags Labels: 6Q0-909-605-VW52.lbl Part No SW: 6Q0 909 605 AH HW: 6Q0 909 605 AH Component: 07 AIRBAG VW52 025 2400 Revision: 06025000 Serial number: 0037TR06BB8G Coding: 0012343 Shop #: WSC 33361 790 00000 VCID: 7DA7FD7461F63ED3CC7-8028 No fault code found. ------------------------------------------------------------------------------- Address 16: Steering wheel Labels: 1K0-953-549-MY9.lbl Part No SW: 1K0 953 549 CP HW: 1K0 953 549 CP Component: J0527 053 0111 Coding: 0000003 Shop #: WSC 33361 790 00000 VCID: 025D8E881808412BB15-8056 No fault code found. ------------------------------------------------------------------------------- Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1 Part No SW: 1Z0 920 803 G HW: 1Z0 920 803 G Component: KOMBI H06 0305 Serial number: 00000000000000 Coding: 110800 Shop #: WSC 73430 031 00000 ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04052 ROD: EV_Kombi_UDS_VDD_RM09_004_SK35.rod VCID: 38292C6002D4DBFB5F1-806C No fault code found. ------------------------------------------------------------------------------- Address 19: CAN Gateway Labels:. 1K0-907-530-V4.clb Part No SW: 1K0 907 530 AD HW: 1K0 907 951 Component: J533 Gateway H16 0233 Revision: H16 Serial number: 4520K101270083 Coding: E9A07F06000202001303 Shop #: WSC 33361 790 00000 VCID: 698FB924057EB27310F-803C No fault code found. ------------------------------------------------------------------------------- Address 25: Immobilizer (J334) Labels:| 5K0-920-xxx-25.clb Part No SW: 5K0 953 234 HW: 5K0 953 234 Component: IMMO H06 0305 Serial number: 00000000000000 Coding: 000000 Shop #: WSC 00000 000 00000 ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03005 ROD: EV_Immo_UDS_VDD_RM09_VW21.rod VCID: 6A8DC6280CF8B96B195-803E No fault code found. ------------------------------------------------------------------------------- Address 42: Door Elect, Driver Labels:. 1K0-959-701-MAX3.clb Part No SW: 1T0 959 701 AA HW: 1T0 959 701 AA Component: Tuer-SG 009 2114 Coding: 0004854 Shop #: WSC 33361 790 00000 VCID: 76B5E25844C06D8B8DD-8022 1 Fault Found: 00120 - Outside Warning Light/Door exit Light Driver Side 012 - Electrical Fault in Circuit ------------------------------------------------------------------------------- Address 44: Steering Assist Labels: 1K0-909-14x-GEN3.clb Part No: 1K0 909 144 J Component: EPS_ZFLS Kl. 68 3001 Revision: 00H17000 Shop #: WSC 33361 790 00000 VCID: 313F1144ED2E0AB318F-8064 1 Fault Found: 03803 - Steering Angle Sensor for Steering Aid 000 - - - MIL ON Freeze Frame: Fault Status: 11100000 Fault Priority: 2 Fault Frequency: 1 Reset counter: 255 Mileage: 116447 km Time Indication: 0 Date: 2016.02.16 Time: 02:54:01 Freeze Frame: Battery Volts: 12.1 V DD Temperature: 38.0°C Count: 2 Steering Angle: 0.00° Count: 0 SteerAng n.Init ------------------------------------------------------------------------------- Address 52: Door Elect, Pass. Labels:. 1K0-959-702-MAX3.clb Part No SW: 1T0 959 702 S HW: 1T0 959 702 S Component: Tuer-SG 009 2114 Coding: 0004854 Shop #: WSC 33361 790 00000 VCID: 48C95CA07EB4AB7B2F1-801C No fault code found. ------------------------------------------------------------------------------- Address 56: Radio (J503) Labels:. 5M0-035-1xx-56.clb Part No SW: 1Z0 035 161 F HW: 1Z0 035 161 F Component: SWING 009 0065 Revision: 0I001001 Serial number: SKZ1Z2K8364845 Coding: 0D0004000001 Shop #: WSC 33361 790 00000 VCID: 313F1144E12E0AB318F-8064 No fault code found. ------------------------------------------------------------------------------- Address 62: Door, Rear Left Labels:. 1K0-959-703-GEN3.clb Part No SW: 5K0 959 703 A HW: 5K0 959 703 A Component: Tuer-SG 007 2101 Coding: 0000144 Shop #: WSC 33361 790 1012544 VCID: 323D1E48E82831AB615-8066 No fault code found. ------------------------------------------------------------------------------- Address 72: Door, Rear Right Labels:. 1K0-959-704-GEN3.clb Part No SW: 5K0 959 704 A HW: 5K0 959 704 A Component: Tuer-SG 007 2101 Coding: 0000144 Shop #: WSC 33361 790 1012544 VCID: 33331B4C173238A36A3-8066 No fault code found. End----------(Elapsed Time: 00:57, VBatt start/end: 12.1V/12.1V)----------- how do i get the freeze frame data using the VCDS?

hi Sir - today i tried with VCDS and if i remove the metering device the VCDS is catching up the same and reports the N290 is open circuit. if i connect it back the error is goes away. the car starts only if i remove the meter devices connectivity and hangs off if i connect it back. if i remove it the VCDS is saying fuel high pressure and shutting the engine after some time. so will that be a metering device issue. and i wanted to confirm before i replace it. is there a way that i can check the metering device for fault? please help. thanks in advance.

hi - greetings and hope all will have a great weekend. please help me for the situation, the car is starting only if i remove the metering device from the high pressure pump and will that be the metering device fault? is there way to test these valves? please advise.

Dear Sir - i was away for while due to various medical reason, i just back and checked the complete car mechanical part, circuits etc. the car is still not starting and when i checked the compression its perfect, the fuel from the fuel tank and the electrical pump are perfect. but the fuel is not coming out from the high pressure pump. i removed the metering devices and tried to check whether the signals are comping in the metering device by cranking, the car is started that means when I remove the metering device and not connected to the HPP the car is starting. do you have any idea why is this sir? your advice will be must helpful.

Hi Dear all i have paid version of VCDS and found the way how to measure the fuel rail pressure live. the issue is this CAR ECM us UDS and test options are very limited in VCDS. the VCDS did not identified the fuel pump issues and intermediate operation. i need to clock the pressure contineously. thanks

Sir - let me try to capture the live fuel rail pressure what is clocking while cranking the engine to see whats going on. can you please help how to do this in UDS protocol ECM? the options in VCDS are limited for these protocol ECM thanks

Dear Sir its - 2.0_ 81 BHP _103 KW TDI CR 2010 DIESEL. can you also suggest the fuse holder layouts if you have for this engine? all the fuses i checked in engine comportment and all ok but i yet to check the one inside the car. do you find any reason as why the temperature needle in the cluster is going extreme end into red and comes back to center if i remove the coolant temperature sensors and the radiator fans stops running otherwise it runs as soon as i put the key in and turn it and the needle is going to red. this is happens in the very cool temperature or stands still of the engine. thanks

thanks Mic. i will check that too but if i remove the G83 and G62 coolant sensors, the the temperature needle is coming back to center, in the cold condition howcome the needle can be in middle or in the extreme right. also the radiator fan is stopped when i remove the sensors. will there be any connection in this? the door modules are removed including the lock barrel and central electonics for service will that be have any impact to immobilizer to be active? if thats the case too, the engine should not crank right and starter is running that means it gets the power. what is the fuse to the HPP inside the engine comportment? can you please help and advise.

Dear Sir - i kept the battery negative terminal removed because the battery gets drained for safety. that could be the reason for immobiliser is active. let me do the test as you instructed and confirm sir. thanks for your help and if there anything else that i need to check please help me sir. thanks in advance and have a great day.

Dear All - i did checked the compression of the cylinder and it clocks 21 bar in all four cylinders. glow plugs are good, the fuses are good in engine comportment. oil level is good. below is my full auto scan from vcds. the car is still not starting. the air filter is clean, the fuel pump is clocking .5 pressure and flow is also good. i have not checked the injector yet. is there anything expert advice to check please help. the car is not starting yet and cranking well. Sunday,08,August,2021,19:02:17:29955 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 21.3.0.0 (x64) HEX-V2 CB: 0.4543.4 Data version: 20210226 DS325.0 www.Ross-Tech.com VIN: TMBBNC1Z9AA151374 License Plate: Chassis Type: 1Z-SK35 (1K0) Scan: 01 03 08 09 10 15 16 17 19 25 42 44 46 52 56 62 72 VIN: TMBBNC1Z9AA151374 Mileage: 116440km-72352miles 01-Engine -- Status: OK 0000 03-ABS Brakes -- Status: Malfunction 0010 04-Steering Angle -- Status: OK 0000 08-Auto HVAC -- Status: OK 0000 09-Cent. Elect. -- Status: Malfunction 0010 10-Park/Steer Assist -- Status: OK 0000 15-Airbags -- Status: OK 0000 16-Steering wheel -- Status: Malfunction 0010 17-Instruments -- Status: OK 0000 19-CAN Gateway -- Status: Malfunction 0010 25-Immobilizer -- Status: OK 0000 42-Door Elect, Driver -- Status: Malfunction 1010 44-Steering Assist -- Status: Malfunction 0010 46-Central Conv. -- Status: OK 0000 52-Door Elect, Pass. -- Status: Malfunction 0010 56-Radio -- Status: OK 0000 62-Door, Rear Left -- Status: OK 0000 72-Door, Rear Right -- Status: Malfunction 1010 ------------------------------------------------------------------------------- Address 01: Engine (J623-CLCA) Labels:. 03L-906-018-CFF.clb Part No SW: 03L 906 018 EJ HW: 03L 906 018 BR Component: R4 2.0l TDI H20 9977 Revision: 42H20--- Serial number: Coding: 00110012040500080000 Shop #: WSC 10259 663 00000 ASAM Dataset: EV_ECM20TDI01103L906018EJ 003008 ROD: EV_ECM20TDI01103L906018EJ.rod VCID: 76B5E25848406D8BA5F-8022 No fault code found. Readiness: 0 0 0 0 0 ------------------------------------------------------------------------------- Address 03: ABS Brakes Labels:. 1K0-907-379-MK70M.clb Part No SW: 1K0 907 379 AK HW: 1K0 907 379 AK Component: MK70 M MASR 0104 Revision: 00H35001 Coding: 0017665 Shop #: WSC 33361 790 00000 VCID: 7BA3F36C7FE230E3DA1-802E 1 Fault Found: 00668 - Supply Voltage Terminal 30 002 - Lower Limit Exceeded - Intermittent ------------------------------------------------------------------------------- Address 08: Auto HVAC (J255) Labels:| 5K0-907-044.clb Part No SW: 3T0 907 044 AS HW: 3T0 907 044 AS Component: Climatronic H15 0401 Revision: 00005001 Coding: 0000001002 Shop #: WSC 73430 790 00000 ASAM Dataset: EV_Climatronic A01006 ROD: EV_ClimaAutoBasis_SK35.rod VCID: 03538B8C0B924823921-8056 No fault code found. ------------------------------------------------------------------------------- Address 09: Cent. Elect. (J519) Labels:. 1K0-937-08x-09.clb Part No SW: 1K0 937 087 D HW: 1K0 937 087 D Component: BCM PQ35 H 103 0575 Revision: 00103 AG Coding: 4E180AB8B00508C04008008011000124410000AE422085605C0440000000 Shop #: WSC 33361 790 00000 VCID: 323D1E48E42831AB497-8066 Subsystem 1 - Part No: 1Z2 955 119 C Labels: 1KX-955-119.CLB Component: Wischer 28011 22 0601 Coding: 00D7B7 Subsystem 2 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB Component: RLS 230110 05 54 0402 Coding: 0730ED 14 Faults Found: 00153 - Windshield Wiper Motor; Driver Side (V216) 004 - No Signal/Communication - Intermittent Freeze Frame: Fault Status: 00100100 Fault Priority: 2 Fault Frequency: 1 Reset counter: 196 Mileage: 116447 km Time Indication: 0 Freeze Frame: Term 15 On Voltage: 12.00 V ON ON Term 50 Off OFF OFF 01493 - Bulb for Blinkers; Front Left (M5) 012 - Electrical Fault in Circuit Freeze Frame: Fault Status: 01101100 Fault Priority: 2 Fault Frequency: 1 Reset counter: 156 Mileage: 116447 km Time Indication: 0 Date: 2015.12.30 Time: 00:38:25 Freeze Frame: Term 15 On Voltage: 11.80 V ON ON Term 50 Off OFF OFF 00978 - Lamp for Low Beam; Left (M29) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 1 Fault Frequency: 69 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:37 Freeze Frame: Term 15 On Voltage: 12.10 V ON ON Term 50 Off OFF OFF 02394 - Parking Light Left Front (M1) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 2 Fault Frequency: 69 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:38 Freeze Frame: Term 15 On Voltage: 12.15 V ON ON Term 50 Off OFF OFF 02395 - Parking Light Front Right (M3) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 2 Fault Frequency: 69 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:38 Freeze Frame: Term 15 On Voltage: 12.15 V ON ON Term 50 Off OFF OFF 00979 - Lamp for Low Beam; Right (M31) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 1 Fault Frequency: 61 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:38 Freeze Frame: Term 15 On Voltage: 12.10 V ON ON Term 50 Off OFF OFF 01495 - Bulb for High-Beams; Left (M30) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 3 Fault Frequency: 61 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:38 Freeze Frame: Term 15 On Voltage: 12.10 V ON ON Term 50 Off OFF OFF 01499 - Bulb for High-Beams; Right (M32) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 3 Fault Frequency: 54 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:40 Freeze Frame: Term 15 On Voltage: 12.10 V ON ON Term 50 Off OFF OFF 01496 - Bulb for Fog-Lamps; Left (L22) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 4 Fault Frequency: 50 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:41 Freeze Frame: Term 15 On Voltage: 12.10 V ON ON Term 50 Off OFF OFF 01500 - Bulb for Fog-Lamps; Right (L23) 010 - Open or Short to Plus Freeze Frame: Fault Status: 01101010 Fault Priority: 4 Fault Frequency: 50 Reset counter: 156 Mileage: 116445 km Time Indication: 0 Date: 2015.11.02 Time: 01:51:41 Freeze Frame: Term 15 On Voltage: 12.10 V ON ON Term 50 Off OFF OFF 01331 - Door Control Module; Driver Side (J386) 004 - No Signal/Communication - Intermittent Freeze Frame: Fault Status: 00100100 Fault Priority: 6 Fault Frequency: 1 Reset counter: 196 Mileage: 116446 km Time Indication: 0 Date: 2015.11.09 Time: 17:43:18 Freeze Frame: Term 15 On Voltage: 12.00 V ON ON Term 50 Off OFF OFF 01334 - Door Control Module; Rear Right (J389) 004 - No Signal/Communication - Intermittent Freeze Frame: Fault Status: 00100100 Fault Priority: 6 Fault Frequency: 1 Reset counter: 196 Mileage: 116446 km Time Indication: 0 Date: 2015.11.09 Time: 17:43:18 Freeze Frame: Term 15 On Voltage: 12.00 V ON ON Term 50 Off OFF OFF 00907 - Intervention load Management 000 - - - Intermittent Freeze Frame: Fault Status: 00100000 Fault Priority: 6 Fault Frequency: 2 Reset counter: 196 Mileage: 116447 km Time Indication: 0 Date: 2015.12.28 Time: 00:55:23 Freeze Frame: Term 15 On Voltage: 11.55 V ON ON Term 50 Off OFF OFF 01497 - Bulb for Blinkers; Front Right (M7) 012 - Electrical Fault in Circuit Freeze Frame: Fault Status: 01101100 Fault Priority: 2 Fault Frequency: 1 Reset counter: 156 Mileage: 116447 km Time Indication: 0 Date: 2015.12.30 Time: 00:38:25 Freeze Frame: Term 15 On Voltage: 11.80 V ON ON Term 50 Off OFF OFF ------------------------------------------------------------------------------- Address 10: Park/Steer Assist (J446) Labels:. 1Z0-919-475-V1.clb Part No SW: 1Z0 919 475 B HW: 1Z0 919 475 Component: PARKHILFE 4K H06 0006 Revision: -------- Serial number: 66641000904029 Coding: 100001 Shop #: WSC 33361 790 00000 VCID: 40D944805A84933BCF3-8014 No fault code found. ------------------------------------------------------------------------------- Address 15: Airbags Labels: 6Q0-909-605-VW52.lbl Part No SW: 6Q0 909 605 AH HW: 6Q0 909 605 AH Component: 07 AIRBAG VW52 025 2400 Revision: 06025000 Serial number: 0037TR06BB8G Coding: 0012343 Shop #: WSC 33361 790 00000 VCID: 7DA7FD7461F63ED3E45-8028 No fault code found. ------------------------------------------------------------------------------- Address 16: Steering wheel Labels: 1K0-953-549-MY9.lbl Part No SW: 1K0 953 549 CP HW: 1K0 953 549 CP Component: J0527 053 0111 Coding: 0000003 Shop #: WSC 33361 790 00000 VCID: 025D8E881808412B997-8056 1 Fault Found: 00888 - Wiper Switch for Intermittent Operation (E22) 014 - Defective - Intermittent ------------------------------------------------------------------------------- Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1 Part No SW: 1Z0 920 803 G HW: 1Z0 920 803 G Component: KOMBI H06 0305 Serial number: 00000000000000 Coding: 110800 Shop #: WSC 73430 031 00000 ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04052 ROD: EV_Kombi_UDS_VDD_RM09_004_SK35.rod VCID: 38292C6002D4DBFB773-806C No fault code found. ------------------------------------------------------------------------------- Address 19: CAN Gateway Labels:. 1K0-907-530-V4.clb Part No SW: 1K0 907 530 AD HW: 1K0 907 951 Component: J533 Gateway H16 0233 Revision: H16 Serial number: 4520K101270083 Coding: E9A07F06000202001303 Shop #: WSC 33361 790 00000 VCID: 698FB924057EB27338D-803C 3 Faults Found: 01331 - Door Control Module; Driver Side (J386) 004 - No Signal/Communication - Intermittent Freeze Frame: Fault Status: 00100100 Fault Priority: 2 Fault Frequency: 1 Reset counter: 196 Mileage: 116446 km Time Indication: 0 01334 - Door Control Module; Rear Right (J389) 004 - No Signal/Communication - Intermittent Freeze Frame: Fault Status: 00100100 Fault Priority: 2 Fault Frequency: 1 Reset counter: 196 Mileage: 116446 km Time Indication: 0 00470 - Company Comfort Databus in Single Wire 011 - Open Circuit - Intermittent Freeze Frame: Fault Status: 00101011 Fault Priority: 3 Fault Frequency: 1 Reset counter: 196 Mileage: 116447 km Time Indication: 0 ------------------------------------------------------------------------------- Address 25: Immobilizer (J334) Labels:| 5K0-920-xxx-25.clb Part No SW: 5K0 953 234 HW: 5K0 953 234 Component: IMMO H06 0305 Serial number: 00000000000000 Coding: 000000 Shop #: WSC 00000 000 00000 ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03005 ROD: EV_Immo_UDS_VDD_RM09_VW21.rod VCID: 6A8DC6280CF8B96B317-803E No fault code found. ------------------------------------------------------------------------------- Address 42: Door Elect, Driver Labels:. 1K0-959-701-MAX3.clb Part No SW: 1T0 959 701 AA HW: 1T0 959 701 AA Component: Tuer-SG 009 2114 Coding: 0004854 Shop #: WSC 33361 790 00000 VCID: 76B5E25844C06D8BA5F-8022 4 Faults Found: 00120 - Outside Warning Light/Door exit Light Driver Side 012 - Electrical Fault in Circuit 00109 - Left Mirror Turn Signal Lamp (L131) 012 - Electrical Fault in Circuit 00131 - Outside Door Handle Illumination/mirror Light Driver Side 012 - Electrical Fault in Circuit 00941 - Exterior Mirror Retract Motor; Driver Side (V121) 012 - Electrical Fault in Circuit ------------------------------------------------------------------------------- Address 44: Steering Assist Labels: 1K0-909-14x-GEN3.clb Part No: 1K0 909 144 J Component: EPS_ZFLS Kl. 68 3001 Revision: 00H17000 Shop #: WSC 33361 790 00000 VCID: 313F1144ED2E0AB330D-8064 1 Fault Found: 03803 - Steering Angle Sensor for Steering Aid 000 - - - MIL ON Freeze Frame: Fault Status: 11100000 Fault Priority: 2 Fault Frequency: 1 Reset counter: 255 Time Indication: 0 Freeze Frame: Battery Volts: 12.1 V PD Temperature: 34.0°C Count: 2 Steering Angle: 0.00° Count: 0 SteerAng n.Init ------------------------------------------------------------------------------- Address 52: Door Elect, Pass. Labels:. 1K0-959-702-MAX3.clb Part No SW: 1T0 959 702 S HW: 1T0 959 702 S Component: Tuer-SG 009 2114 Coding: 0004854 Shop #: WSC 33361 790 00000 VCID: 48C95CA07EB4AB7B073-801C 6 Faults Found: 00121 - Outside Warning Light/Door exit Light Passenger Side 012 - Electrical Fault in Circuit 00110 - Right Mirror Turn Signal Lamp (L132) 012 - Electrical Fault in Circuit 00132 - Outside Door Handle Illumination/mirror Light Passenger Side 012 - Electrical Fault in Circuit 00942 - Exterior Mirror Retract Motor; Passenger Side (V122) 012 - Electrical Fault in Circuit 01331 - Door Control Module; Driver Side (J386) 004 - No Signal/Communication - Intermittent 01334 - Door Control Module; Rear Right (J389) 004 - No Signal/Communication - Intermittent ------------------------------------------------------------------------------- Address 56: Radio (J503) Labels:. 5M0-035-1xx-56.clb Part No SW: 1Z0 035 161 F HW: 1Z0 035 161 F Component: SWING 009 0065 Revision: 0I001001 Serial number: SKZ1Z2K8364845 Coding: 0D0004000001 Shop #: WSC 33361 790 00000 VCID: 313F1144E12E0AB330D-8064 No fault code found. ------------------------------------------------------------------------------- Address 62: Door, Rear Left Labels:. 1K0-959-703-GEN3.clb Part No SW: 5K0 959 703 A HW: 5K0 959 703 A Component: Tuer-SG 007 2101 Coding: 0000144 Shop #: WSC 33361 790 1012544 VCID: 323D1E48E82831AB497-8066 No fault code found. ------------------------------------------------------------------------------- Address 72: Door, Rear Right Labels:. 1K0-959-704-GEN3.clb Part No SW: 5K0 959 704 A HW: 5K0 959 704 A Component: Tuer-SG 007 2101 Coding: 0000144 Shop #: WSC 33361 790 1012544 VCID: 33331B4C173238A3421-8066 1 Fault Found: 02071 - Local Databus 004 - No Signal/Communication - Intermittent End----(Elapsed Time: 01:01, VBatt start/end: 11.8V/11.8V. VIgn 11.8V)-----

thanks Mic, and will try and update shortly. great suggestion from all of you and great knowledge. thanks

Dear Ken - thanks for your response. let me check that tomorrow and confirm. the fuses in the engine comportment were already checked with test light and all ok. but i have not checked near to the driver seat under the dashboard. can you please help me the fuse number for ECU? i have not checked the relay on the fuse tray in the engine comportment. also if the fuse to the ECU is blown, will the VCDS able to collect the logs that i pasted above? oil level is within the limit and good. just before the high mark and it was replaced just few mile before. thanks

Below is my scan data for engine module Sunday,08,August,2021,19:02:17:29955 VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64 VCDS Version: 21.3.0.0 (x64) HEX-V2 CB: 0.4543.4 Data version: 20210226 DS325.0 www.Ross-Tech.com VIN: TMBBNC1Z9AA151374 License Plate: Chassis Type: 1Z-SK35 (1K0) Scan: 01 03 08 09 10 15 16 17 19 25 42 44 46 52 56 62 72 VIN: TMBBNC1Z9AA151374 Mileage: 116440km-72352miles 01-Engine -- Status: OK 0000 Address 01: Engine (J623-CLCA) Labels:. 03L-906-018-CFF.clb Part No SW: 03L 906 018 EJ HW: 03L 906 018 BR Component: R4 2.0l TDI H20 9977 Revision: 42H20--- Serial number: Coding: 00110012040500080000 Shop #: WSC 10259 663 00000 ASAM Dataset: EV_ECM20TDI01103L906018EJ 003008 ROD: EV_ECM20TDI01103L906018EJ.rod VCID: 76B5E25848406D8BA5F-8022 No fault code found. Readiness: 0 0 0 0 0

Dear All - i have SKODA OCTAVIA MK2 2010 model. I am from India, i had flat battery and recharged and cooked up to the car and started for running at idle. it was running fine and all ok. i went away from the car and in some time i heard a rough idle from the car and hearing the radiator kicking off to rotate with huge sound and the car stopped. i checked the battery, its fine, the fuel pressure and flow is fine at both inlet side and at the HPP side. i have not checked the compression yet, however the car is not starting at all. its crank well but not starting. the radiator is keeps running when ever i switch on the ignition but not started the car. i checked the coolant temperature seasons G62 and on radiator line and its good. my next check is to check the thermostat and the speed sensor, compression. is there anyother check i need to do to narrow down the issue? please help. no engine module error in VCDS. thanks in advance

hi All - i have Skoda Octavia Mk2 which has UDS ECM and i do not think i can be able to set the timing with VCDS. My question how to i measure the existing injection timing ? is it possible by VCDS or mechanically? i wanted to check because since i replaced the timing belt, there is black smoke coming out of exhausts which is replaced by the SKODA ASP. i wanted to check the timing and ensure both cam timing synchronize with crank timing and injection timing. i have the injection timing checking tool with adapters. can you please help