Jump to content

octaviaprime

Members
  • Posts

    43
  • Joined

  • Last visited

Profile Information

  • Location
    london

Car Info

  • Model
    mk2 octavia vrs petrol

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

octaviaprime's Achievements

Contributor

Contributor (5/17)

  • First Post
  • Collaborator
  • Reacting Well
  • Conversation Starter
  • Week One Done

Recent Badges

1

Reputation

  1. I did manage to do this. You require the drivers door loom and the control module and switch. You just straight swap that over. You may need to code it but mine worked straight away. The rear is a little more difficult as I swapped over the mechanism and the control unit as I think they are extended for the winder handles. The loom needs a power supply so you need to tap into your fuse box so plug in your connector and run the cables to correct pin for the door connector. The earth points are in the b pillar buy the belt anchor point. You need the canbus high and low for the controller so tap into your canbus cables but make sure you get them the correct way round for the pins in the door connector. My donor car was a hatchback but my car was an estate so the door car tops had to be swapped so I didn't have a hole but if you get the correct door cards you can skip this step. It was an Easy weekend job make sure you have the wiring connectors makes it alot easier to swap unless you want to make up a small loom. But I had the donor car so just pulled everything out and cut and made fit what I needed
  2. When I was reversing tonight with no extra throttle just idle the car was bouncing around like when it's on the brake. The lights a dimming even though the are leds so I don't know what it could be
  3. No fault coded coil packs are OK no misfires. Sounds like an off beat idle. Could it be balance shafts or dmf
  4. Hi guys have been doing some research with no luck on here. Long story short. The car is a 2007 octavia vrs tfsi stage one map precat delete ram air cone filter 50mm lowered on coilovers. Thursday last week car drove perfectly fine. Friday morning got in it to go to work bit of a bouncy idle with a bit of a misfire on cylinder 2. Check spark plug ok put the old one in no different swapped for the original on still the same. Sitting around 750. Going to try the throttle body reset tomorrow. noticed today when in traffic. When I had my foot on the brake the car would bouncy at idle like being on a trampoline. Take my foot off it would stop? So confused. Just want my car to idle properly 😪. Checked vac lines to brake booster no cracks apparent. Sorry for the long one guys Thanks for the help in advance.
  5. I have 20mm on the rear and 15 up front on standard suspension and fills the gap lovely witha couple of mm fron the arch. I am looking at the stance uk kit to lower my 07 vrs so i dont know how they ride yet though.
  6. Hi langers i dont have vcds so no access at the moment will have to hear back from a friend of mine who has it
  7. Hi guys Hoping for some help. My cruise control has been a bit tempremental since changing the clutch pedal master cylinder. I could live with that not to bad. Today i was driving to work had the cruise control on at 50 it went off and the esp light has come on. I know i havd worn wheel bearings at the rear would this cause the cruise control to switch off of they deviate from the front speed sensors. This has made me think its a mechanical problem rather than electrical. Plus dont really want to pull all the wiring apart
  8. Hi guys I have finished a a full engine rebuild and been enjoying the car but now want to give the old girl some more punch with more boost. I looked up the spec for a k03 and 0.6 bar 8 psi is the max flow. So remap doesn't seem worth doing just yet as I I have a new hpfp new belts and a full rebuilt head and an uprated diverter valve. So putting a new turbo on seems ok and I have the standard injectors so remap then allows the for the turbo being able to boost without being strained. I no there are kits but looking at them I have most of the parts apart from the injectors everything else I have fitted or the car already has like the intercooler precat removal. If anyone can help that would be great
  9. I am undertaking this little project myself I have everything from from my donor car do the handle drives fit the motors
  10. How much would it be dunno if you can pm on here still learning this site where everything is
  11. Do you have the door window switch for the driver's side. If so how much
  12. Do you have to door switch that controls the window. Is it just the front window one which is the one I am after Alex
  13. Been a bit quite lately but fitted a new Flexi pipe and heat wrapped my down pipe to the cat. Refurbed my alloys and my engine cover top. painted most of my interior
×
×
  • Create New...

Important Information

Welcome to BRISKODA. Please note the following important links Terms of Use. We have a comprehensive Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.