KrisssM

I understand all that and admire their work. I will try to buy the cable asap, and fyi, I got the tail lights second hand for real cheap.

Let the car go to sleep, now fault codes disappeared.

The cable is just quite expensive and I haven’t got the resources for it right now, maybe you could still help me?

I forgot to mention that all the lights in the rear are working.

Hi, unfortunately I have not been able to buy the oem cable, so I have to use the old software. I hope it is okay. The adaptation map could have some changes as well from coding the headlights, although that shouldn't matter? The auto-scan is before clearing all dtc-s, however, after clearing it, these 3 remained. 10515 - Bulb for Left Tail Light B12BE 01 [009] - Electrical Failure Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 74 Mileage: 62506 km Date: 2021.05.13 Time: 10:16:16 10771 - Bulb for Right Tail Light B12BF 01 [009] - Electrical Failure Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 1 Reset counter: 74 Mileage: 62506 km Date: 2021.05.13 Time: 10:18:14 565764 - LED Light Bar B1664 31 [009] - No Signal Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 5 Fault Frequency: 1 Reset counter: 209 Mileage: 59618 km Date: 2018.01.01 Time: 15:01:17 adpmap-09-5Q0-937-086-AA_TMBLJ9NE8F0040922-20210306-1213.CSV Log-680BMM-TMBLJ9NE8F0040922-62506km-38839mi.txt

Hi, I have fitted Oem LED taillights on a Combi, I coded everything according to the guide under VCDS adaptations thread. But the car still shows faults for “Check left tail light!” and “Check right tail light!”. I’ll post the adaptation map also just in case. adpmap-09-5Q0-937-086-AA_TMBLJ9NE8F0040922-20210513-1104.csv

I have enabled US blinkers as park/side lights, but I want to disable H15 bulbs as side lights alltogether, but keep them as high beam of course. What channel should I disable in adaptations?

I need help choosing the correct rain sensor. I currently have no sensor installed on my car, manual air conditioning. So I would need to run all new cables as well. But I have read that not all rain sensors work. All these are fitted to Oct III, would all of these work if I only want to use them as rain sensor and light sensor for CH/LH as well? 5Q0 955 559 Rain sensor 5Q0 955 559 A Rain sensor 5Q0 955 547 A Rain and humidity sensor 5Q0 955 547 Rain and humidity sensor Thanks in advance.

It worked both ways, although I only kept them with DRL. With side lights, after turning the ignition off, side lights did not remain on. Otherwise, thanks a lot. Still any idea, how to keep the gauge cluster from dimming when light switch is on O and it is dark outside?

Thanks a lot, will try it out later

Here. Log-12345-TMBLJ9NE8F0040922-59141km-36748mi.txt adpmap-09-5Q0-937-086-AA_TMBLJ9NE8F0040922-20210306-1213.CSV

I also read about turn signal bulbs melting with halogen headlights. If they are dimmed to 30%, will they be in a safe spot or rather not?

How could US blinkers be coded to work as DRL lights? Currently have disabled original DRL lights and I use fog lights instead, now I would like to add US blinkers as well. I already have US blinkers working with low beam Another question, is there any way to code gauge cluster to be on all the time and not dim when it is too dark?

Basically I would want to have US blinkers on with low beam and also work as drl with fog lights. I currently have US blinkers working together with low beam. I also have only fog lights as drl(original h15 drl not working), but I would want to have US blinkers on as well.

I have enabled US blinkers with low beam already, if it helps any bit.