ujtordai

Hi All, I'm sorry, I did not describe clearly what I would like. I would like to replace or repair the arm. I have misty memories about it. - Remove the negative pole from the battery. - remove the airbag and the steering - remove the cover of the rod of steering but I have no details. I attached a picture what is my problem, I don't know something is broken inside of the arm mechanical part or not, or just dislocated.

Hi All, There is a number on the EGR valve which begins with letter V if this number is below 600 it should be adapt it the number above 600 not need the adaptation process. Replaced the EGR valve to another new one where the number is above 600. I cleared all error codes it works as we expected.

Hi All, How to access windscreen washer lever? It's a tiny bit dislocated, I would like to put it onto the normal place. Thank you in advance.

The car service technician person stated he checked all and all is perfect. It should have been to check by myself.

I just hope. In the service, the car technician mechanic assures me it has not damaged. What is the problem is the most common cases with the cables? How can we determine the cable is bad? Each cables one by one should check by endless resistance and it not short to ground. Can be occurred this any other problem except for the "broken wire on the connector"? Thank you in advance.

Hi How Can I do the adaptation It has an error code, and I cannot clear it, therefore the Measurement block ö8 is disabled. I used the VCDS. 4900 - EGR Sensor 1 P0405 00 [175] - Signal too Low I cannot clear this error code. Thank you in advance.

One more thing, Should I enter any values, or it go ahead automatically. Thanks

Thank you I will try it.

Thank you for your answer, The EGR valve is a brand new VAG (now I fixed it in my original question) What kind (exactly what should set) of basic settings needed in the engine module? Thank you

Hi All I would like to get some help. After replacing the EGR valve, (brand new VAG) the engine light is on, cannot clear the error codes P0405 and P0403. My questions are, - What can be the cause of these codes? - Is it possible to do the learning process with VCDS (or other software) to adopt the new EGR valve? How should this resolve? Thank you in advance.

Three days ago I got an ERROR code (P0403 00 [040] - Malfunction) the mileage is 203.000 Km. I should replace the EGR valve ( 7.24809.16.0 ) and also I shud replace the valve which responsible for the smooth engine shutdown (makes a decompression when the engine shutdown), maybe the name is shut-off valve ( 7.14393.26.0 ) Cheers

I have service book of course but I interested in the practice, not the service book. When I can expect that when I must replace the Diesel Particle Filter, fuel injectors, or turbocharger? I interested in just the other Superb II user's practice who already replaced the mentioned spare parts.

Hi Thank you for your answer. I find it, but not found. May I ask you drop me an URL of that? Thanks.

Hi All, I have a sedan Superb II. 2.0 CR TDI DPF car. Is there exists collected main parts replace estimation by mileage? For example - About 160.000 Km replaced the timing belt and water pump (based on the official guide it should be replace at 210.000 Km) - About 185.000 Km replaced the Dual Mass Flyweight with a clutch and axial pneumatic bearing, (the diaphragm springs went out) - About ..... Km replaced the Turbo Charger - About ..... Km replaced the Diesel Particle Filter - About ..... Km replaced (or repaired if it is made by Bosch) the Fuel injectors etc. May I ask you guys, to share with us your experiences when happened the main parts replacement by mileage in your superb II CR TDI car? Of course, I know it depends on the "drivers leg" with other words the driving habit, what fuel used (normal or premium) and, the usage (city or highway) etc. I use my car in the most common cases in the city (the city is about 80%, the country roads 15%, the highway 5%) Thank you in advance.

Hi all, In meantime I done it. I removed the four screw which fixed the rail of the seat. I not disconnected the battery negative or earth cable because I not disconnected the air bak cable of the seat. The key is XYN / Spline 12pt.

Hi All, How can I replace driver side seat belt buckle? Is need to remove the seat? Is need to disconnect the battery? (for airbags)? What happen when I reconnect the battery, I should be set a lot of end or default position maybe. Is it correct? One more thing, what kind of tool/key needed for remove seat? As I know it is not torx. Thank you in advance

Thank y ou, I will try it.

Hi All, May I ask you, how can I set the service interval with VCDS? Now the oil replaced and I would like to set the next service notification time when I reach the next (after 15.000 km) oil change time mileage. Thank you in advance.

Hi All, What does the fault code means, and what should I do in this case? Is it any relation to my current problem? Address 09: Cent. Elect. Labels: 1K0-937-08x-09.clb Control Module Part Number: 1K0 937 087 K HW: 1K0 937 087 K Component and/or Version: BCM PQ35 H+ 103 0615 Software Coding: 46990AB8E00508C04010008011008164427000AE532081605C0040000040 Work Shop Code: WSC 49044 233 90754 VCID: 39794BC1B0880189C8-806C 1 Fault Found: 02723 - Control Circuit for Power Supply Relay (Terminal 50) 012 - Electrical Fault in Circuit - Intermittent Freeze Frame: Fault Status: 00101100 Fault Priority: 1 Fault Frequency: 19 Reset counter: 18 Mileage: 188787 km Time Indication: 0 Date: 2012.05.15 Time: 08:51:50 Freeze Frame: Term 15 On Voltage: 12.15 V OFF ON Term 50 On ON ON

Hi All, I find somebody who have an installed ETKA, for idebtify by chasis number, what is the part number of the driver side seat belt socket (The steering wheel on left side) which proper for my superb . May I ask somebody to do this? I can send chasis number in PM. Thank you in advance. (The car is Skoda Superb 3T4 year2010)

Hi Another experience. If I fastened the seat belt in reverse it can be another workaround temporary for this problem.

I noticed the following, if I replaced the seat belts of driver and passenger exactly fastened the passenger belt into driver's slot and vice versa then not flashes the control lamp. But it a bit uncomfortable.

Hi All, I would like to get some help. The seatbelt warning light randomly flashes, when I driving, of course it always fastened. Somebody had a same experience? What will be the cause of it? Thank you in advance.

pl. sent, thank you in advance.

Hi All, I find somebody who have an installed ETKA, for idebtify by chasis number, what is the part number of the cabin air ventillator which proper for my superb . It can be proper also if show me an online parts catalog. I should be replace it because it is creaking. May I ask somebody to do this? I can send chasis number in PM. Thank you in advance. (The car is Skoda Superb 3T4 year2010)