Gazdok

I fitted a RVC to our SII estate - I have attached the VCDS of the 6C controller after calibration. If your OPC is suddenly playing up and you should not have done anything to it for the RVC installation, go back to the last coding where the OPC was working and delete the DTCs. Otherwise it may have coincidentally become faulty. RVC_cal.txt

These are the part numbers for LED rear light clusters. UK Left - 3T9945095B - NO LED fog Skoda 462 FL SX UK LH F03483500 00 148 EC Left - 3T9945095A - With LED fog Skoda 462 FL SX ECE LH F03483000 00 UK Right - 3T9945096B - With LED fog Skoda 462 FL DX UK RH F03484500 00 149 I did not bother with a EC right as that does not have a LED fog light. If you would like a LED fog on the right you need to look for a UK right. It must be more expensive to build 4 different light clusters rather than have 2 for one model.

Silver1011, You are correct. I had mine out and swapped the over. The fog only lights up in the right one. When you look at the light cluster, it looks as if there is something in the slot for the left fog, but there are no LEDs visible. The reverse is true for the continental european ones. They seem to have a fog only in the left cluster. The wiring however is the same for left and right.

I have the LED FL version. I think I have 2x LED fog lights fitted but only one activated. I have checked on the wiring diagram but have not attempted an activation across yet. Rear light cluster wiring.pdf M4 on the left tail light has a NSL - Nebelschlußleuchte - as well as M42 on the right, but it is not connected on the left. I have messed up my rear cluster when I tried to activate with VCP and back to square one.

I have a VCP and VCDS and neither allow the 2. fog light to come on. VCP is probably more advanced and I have not seen any posts that describe that it works via coding. But right and left hand drive have one on the opposite sight I think.

For most wires on the RVC only connect the same colour patterns. For R/W and R/Ge (yellow) they can go on the same as both are switched 12V+. Keep the Can buses as twisted as possible.

I see from your profile that you have a Superb II as well. Would you not want to do that one too and post a how to.... Just because I have a Superb II and have thought about a 2. rear fog light. Sorry, a bit cheeky.

craigandrew, I took the Red/White within the cable loom where it goes down from the fuse board under the floor carpet in the driver side footwell. Look at my picture 6. Janar, you should NOT have an Or/Gr in the RVC system. I just mentioned it, because it is another CAN bus system on the car. If you do not connect the CAN bus or connect it wrong the TV or RVC will not get and send the correct information to the gateway.

The orange/brown and orange/purple are the Can-supplies. They are a MUST and cannot be left unconnected. There are different Can buses in the Superb. Make sure you connect it to the corresponding colours.Or / Br Can low, Or / purple Can high Infotainment. Or / Gr Can high drive. Or / Sw Can high .... The Red/White and the Red/Yellow are both switched 12V. I connected both onto a Red/White in the A-pillar. Brown is ground. You connect the components in the order: Camera - TV Tuner - Camera controller - Columbus.

The handle will fit without the bracket. It has small plastic "hooks". Make sure you rust proof the cutout in the tailgate and then use a thin film of silicone.

It looks o.k. PNs are correct.

The RVC controller PN I used is at the top. You can use Tiguan, Passat...

Except for the TV tuner and camera lead I bought my parts separately on EBAY. It was used but o.k. I have seen the pin outs when I was looking for my loom and I think the pinouts were different for the RFK HIGH 7N1971327 and the TV tuner loom 7N1971327b. The part numbers are different... You still need a Fakra Z lead from the camera to the controller and the camera needs a power supply - white leads on my picture with the loom on the floor.

This should do the job. Just follow the instructions or route the cable your own way. You have to cut out the tail gate for the larger boot handle. I think I paid half that price though.

The lead for TV Tuner + RFK High: 7N1971327b. You buy this from VAG. If you do not have or do not want to use the TV tuner any more you use : RFK HIGH: 7N1 971 327. I guess it is different from 7N1971327b, but I can not tell you the pin outs. A Columbus / RNS510 happily runs a camera instead of TV tuner, i.e. you can ditch the TV. The link below shows the setup in the car. https://volkswagen.7zap.com/en/ra/sharan/sha/2016-689/9/971-972070/#1