peekay34

I have the same issue has been looked at 3 times by Skoda but still there ... .this time I recorded the noise going back for the fourth time.

You have to have the memory motor in the housing coding is not enough….

I have the Alcantra Seats in my Sportline. For some unknown reason that I can't work out Skoda does not supply the mirror that does not mirror dip. They only included that option with the lessor model with leather memory seats (so I am told.) My car is the top of the range with all options (lane assist read radar) available in Australia but still no mirror dip. I did some research and found that the mirror with memory function is missing from my car. So I ordered the mirror with memory function simply replaced the mirror and recoded and it worked. Since I dont know what model you have I can only advise mirror assembly I purchased. 57C857507K pretty sure thats the part no. https://www.oemvwshop.com/57c857507k-rear-view-mirror-housing-p2335210/

Ambient Lighting 30 Colours In VCDS go to module 9 Security Code 31347 The colors are given in RGB coding RGB is the acronym for Red-Green-Blue. Colors are made up of 3 parameters, with values in a range between 0 and 255. Each color is encoded with a percentage of (Red, Green, Blue). For example, a pure yellow can be defined as rgb (255, 255, 0). I have attache an example of the colours I have set but you can use this as guide for more colours RGB Color Codes Chart (calculatorx.com) Changes can be started use lines in attached doco from 11-30 to add colours to existing 10 already enabled. Rotwert Farbe = Red Gruenwert Farbe - Green Blautwert Farbe = Blue ambientLIGHTINGCODEING.docx

Enable Traffic Information (TMC) using - VCDS tweak...... Tested in Australia Step 1. On "Select Control Module" option click "Select" Step 2. Select "5F-information Elect" Step 3. Select "Adaptation" Step 4. Using pull-down menu, select "Fee Based Traffic Information (TMC)" channel Step 5 Change default value "0" to 1024

ACTIVATE THE Different Display type on virtual cockpit (It puts a red inner ring and RS carbon effect) 1.- module 17 (instrument panel ) 2.- Go to adaptation 3.- in tube_version ( representation of tubes ) change the original value " variant 3 "for" Variant 2 " gives more colours in the virtual cockpit but you can try others.

DISPLAY AIR CONDITIONING FAN SPEED IN AUTO MODE Having it in auto mode, the fan speed leds are not shown, this activates it Go to Module 08 - Air conditioning electronics Enter Extended Coding , activate top right, Bytes mode Go to byte 11 Activate Bit 6 Confirm

Instrument Cluster Road Sign Recognition activation Enables option to show current speed limit based on the image recognition function of the front facing camera. Module: 5F (Information electronics) Adaptation → Channel: Car Function List BAP Gen2 - traffic sign recognition 0x21 New value: active Module: 5F (Information electronics) Adaptation → Channel: Car Function List BAP Gen2 - traffic sign recognition 0x21 msg bus New value: Databus extended Module: 5F (Information electronics) Adaptation → Channel: Car Function Adaptations Gen2 - menu display road sign identification New value: active Module: 5F (Information electronics) Adaptation → Channel: Car Function Adaptations Gen2 - menu display road sign identification over threshold high New value: active Module: 5F (Information electronics) Coding → Long Coding → Byte: 24 → Bit: 6 New value: active Module: A5 (Front Sensors Driver Assistance System) Security Access → Code: 20103 Module: A5 (Front Sensors Driver Assistance System) Coding → Long Coding → Byte: 01 → Bit: 0 New value: active Module: A5 (Front Sensors Driver Assistance System) Adaptation → Channel: Road Sign Detection Fusion Mode New value: Road sign fusion Module: A5 (Front Sensors Driver Assistance System) Adaptation → Channel: Display end of speed limit symbol New value: active Module: A5 (Front Sensors Driver Assistance System) Adaptation → Channel: Valid additional characters New value: 00100111 Module: 17 (Instruments Cluster) Coding → Long Coding → Byte: 05 → Bit: 2 New value: active Reboot infotainment unit by pressing and holding volume knob for 10 seconds. On the infotainment display go to Car → Setup → Driver Assistance Settings → Dynamic Road Sign Display and enable "Show in instrument cluster" option. On the infotainment display go to Car → Setup → Instrument Cluster Settings and enable "Dynamic Road Sign Display" option.

Central Lock Acoustic Confirmation when Locking activation (works with car alarm not tried on horn alarm) Enables sound confirmation when locking and unlocking car, as well as option to control this feature from the multimedia system menu. Module: 09 (Central Electronics) Security Access → Code: 31347 Module: 09 (Central Electronics) Adaptation → Channel: Acknowledgement signals - Akustische Rueckmeldung Entriegeln New value: active Module: 09 (Central Electronics) Adaptation → Channel: Acknowledgement signals - Akustische Rueckmeldung Verriegeln New value: active Module: 09 (Central Electronics) Adaptation → Channel: Acknowledgement signals - Dauer der Akustischen Rueckmeldung vom Einfachhorn New value: Kurz Module: 09 (Central Electronics) Adaptation → Channel: Acknowledgement signals - Akustische Rueckmeldung global New value: active Module: 09 (Central Electronics) Adaptation → Channel: Acknowledgement signals - Menuesteuerung akustische Rueckmeldung New value: active On the infotainment display go to Car → Setup → Lock & unlock and enable "Acoustic confirmation" option.

Side Mirror Tilt on Reverse activation ( this will only work if the mirror in the car has this capability I replaced mine so it would work) Passengers mirror will tilt down when in reverse and control switch set to passengers side. Function can also be controlled from main unit screen. Module: 52 (Passenger door electronics) Coding → Long Coding → Byte: 04 → Bit: 2 New value: enable Module: 52 (Passenger door electronics) Coding → Long Coding → Byte: 04 → Bit: 3 New value: enable Module: 09 (Central Electronics) Security Access → Code: 31347 Module: 09 (Central Electronics) Adaptation → Channel: Access Control 2 - Spiegelabsenkung bei Rueckwaertsfahrt New value: Active Module: 09 (Central Electronics) Adaptation → Channel: Access Control 2 - Menuesteuerung Spiegelabsenkung New value: Active

Disabling or turning down the Soundaktor Disabling or turning down the Soundaktor reduces the engine sound especially in sport mode. From the VCDS main screen click the button “Select” Click the button “A9 Structure Borne Sound” Click the button “Adaption 10” Use the Channel drop down and select “Volume of structure borne noise actuator” For me it was the only one. Enter a value. Default value is 100, setting 50 would reduce the sound by 50%. 0 would turn it off completely. Click “do it”

ACTIVATE AUTO LIGHT ASSIST Necessary Sensor (A5) on the windshield ("Multifunctional Camera") 1- Modul 09 Electronic Control Unit Security access: 31347 Let's go to Adaptation : Fernlicht_Assistent Modify Erweiterte Fernlichtsteuerung to: AFS: FLA: Fernlicht ueber AFS Mark Menusteuerung Fernlichtassistent as: Available Mark Menusteuerung Fernlichtassistent Werkseinstellung as: Available ** If you also want the LA (FLA) to always remain active even if you turn off the car, you must check: Fernlichtassistent reset: inactive We confirm the Changes. The light assistance should appear in the car menu: Vehicle Settings / Lights ( note: Do not activate until the process is finished ) 2- Module A5 Front sensor Extended coding (enter byte mode) In Byte 21, Activate Bit 5 (Even if you put Bit 5-7, really only 5 is marked. Byte 21 should be set to "HEX 20") We confirm the Changes. 3- Reset the Lights: Finally Reset lights in the Infotaiment-> Car-> Settings-> Factory settings-> Restore settings / data separately-> Lights Ready Using the Auto Light Assist The first touch of the High Beam lever activates the Auto Light Assist, The second goes to Fixed high beams. Please note others have posed this coding I should thank them for doing that....

DAYLIGHTS (DRL) OFF WITH THE PARKING BRAKE ON This modification allows us to leave the daytime lights off while we have the parking brake on with and without contact. Very useful in low battery conditions. 1 - Module 09 - Electronic control unit. 2 - Adaptation 3 - Enter Aussenlicht_Front 4 - We look for Tagfahrlicht Dauerfahrlicht bei Handbremse abschalten - (Change value to On) 5- Enter code 31347 and accept NOTE: Handbrake always on: Contact removed - auto lights roulette: Off Contact removed - lights roulette 0: Off Contact on - lights roulette 0: Off Contact on - car lights roulette: On

So coding this has been done on a 2020 Sportline Karoq most if not all of this coding is common on most VAG cars and has worked on my car. This was coded on a HEX2 cable from RossTech. I take no responsibility for any issues that may occur on your car should you choose to code these options. Backup all settings\adaptions before you do any coding (This is so you can reference back to previous settings). Please note that VAG do not take kindly to changing coding so may affect your warranty revert any coding if taking your car in for service. I I upload when I get time.

Do you have the latest version of the VCDS cable?