skolaeast

Hi, is there anybody, who can read the PIN from cluster EEPROM? EEPROM code is below. THX budikz F2.bin

Hey guys 🙂. It works!!! 🙂. The problem was in the black connector on clusters. I had connected only Terminal 15 and 30 as +12V and 31 as GND, but its need to connect PINs 4 and 6 as parking lights left and right on +12V too. Light switch and potenciometer is not needed (you can input only +12V on BSG pin XS1/2). Thank you so much for your help. Summary Clusters black connector - Pin 5 +12V Terminal 15 Pin 7 +12V Terminal 30 Pin 8 GND Terminal 31 Pin 4 +12V (right parking lights) (if you have a light switch -> connect to Pin 58(b) of light switch) Pin 6 +12V (leftparking lights) (if you have a light switch -> connect to Pin 58(b) of light switch) Clusters green connector - Pin 7 -> XS6/3 CAN L motor Pin 8 -> XS6/5 CAN H motor Pin 9 -> XS2/12 CAN H comfort Pin 10 -> XS2/9 CAN L comfort Pin 24 -> XS6/11 Wake UP BSG - XS4/12 +12V Terminal 15 XS4/8 GND Terminal 31 XP2/1 +12V Terminal 30 XP4/2 GND Terminal 31 XS1/2 +12V backlight of clusters (or connect to 58b from light switch and light adjuster)

Now I bought a light switch... I connect a few pins what I thing I need... Backlight of switch is working perfect... On Zero position, on next positions and intesity of backlight is working too... But clusters nothing... I have connected light switch with that pin on BSG and nothing... 😞 So, what I need else?

So, is there any chance to send a signal to BSG to light on backglight or I have to buy light switch? 😞

That would make sense and that's what I was worried about. So I need light switch with this range adjuster. This IC will be in this schema...

No, from begin it was a project for clusters on table and communication with car games... Everything works, but only this not. In car the backlight works.

Please, if you know how to connect it, help me... I've been trying to do it for the second month and still nothing. I tried almost everything and I am not sure if is still BSG OK :-D.

But backlight of clusters works at everytime, when is switch of lights in any position without 0. You doesn't have a key in ignition... I'm really over, only knows, what type of signal sent to XS1 T6c/2... 😞. Maybe next question... if diagnostic test can light on backlight of clusters -> If I buy Arduino -> CAN BUS module, can I send some command via Arduino to CAN communication (like a "Output test" in VCDS app)?

OK... now I have important pins for run BSG... it is XP2/1 +, XS4/12 + and XP4/2. For communation whith cluster I used CAN-BUS communication Motor (2 pins), Comfort (2 pins) and Wake UP pin (BTW, I am not sure if I really know what does it mean). It is the minimal, what I need to run BSG. (at the last time I had connected many Plusis to BSG... Everything what was Input from fuse or everything what was POSITIVE from terminal 30. for eaxmple "back window heating etc." Now I connected only important 3 pins. Terminal 15,30,31 and communication is still OK and I have on clusters error of power steering and airbag.)When I connect VAG COM cable to K - line, i Can make a "Output Tests". With this function I can light on it... So... i have a China module step down and up and I tried to simulate continual voltage UP from 0V to 12V to pin XS1/2 and nothing happened. I have common Ground and +12V from my Power Supply and the output + to XS1/2 and so nothing... absolutely nothing... Please 🙂 help me to solve this simply thing...

I understand it now :D thx so much for explain this 🙂. " you did reference your inputted variable voltage to the same 0V/earth as the cluster is getting, did you?" Yes, i had a common GND point, but nothing happend. Now I have maybe about ten + cables to BSG and I am not sure, which I need and which not. Maybe I have some extra or I miss one... 😞 I will try it from begin. If you have some ideas, which pins on BSG must have +12V and which GND... 🙂

This I have... But i do not understunding to "Reference to continuation of wiring". Where is the continuing... for next things above i will look tomorow. I have an New Year party 🙂 THX a lot for this time. Happy New Year to all of you.

I used a 10k OHM potenciometer (with LED diod) and feed 0V-12V to XS1 (T6c/2) in BSG (J519) and nothing going on... My LED diod with resistor is working, but backlight nothing... I founded that page about setting of backlighting, but I don't understand it... 😞 Everything work me... I can connect the clusters to PC and via app play a game and show real speed on clusters it is perfect, but this simply think like is backlight i can not run :(. I do not understand, what does it mean that A4, A9 etc. and continuing of cable [32] etc.

So... How can I simulate a light switch And connection to T6c/2? Any ideas? Or I have to buy a light switch? 😀 I do not want to buy complete switch

I am not sure, but it is from junior or classic version of Fabia between 1999 to 2003 without computer.

It's a perfect for anything next what I want to do, but... I'm founding a pin at BSG which get from Light switch info about parking lights which starts light in car... It must be a simple, becouse light switch does not have a CAN communication, it is only switch, nothing more... but I can't found it 😞 I have only this type of documentation and this is a light switch.... I thing, that I have to know where is going pin (terminal) 58 cable 1 mm green/blue at continuing [86]. Everything is described (not so good, but is), but this type of continuing isn't...