-
Posts
25 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Shop
Events
Downloads
Posts posted by hitmn
-
-
20 hours ago, Gti Jazz Blue said:
It would be interesting to find out how he has it wired - is he using it in 4 + 4 configuration - so a 4 Ohm load across each sub output?
Yes.
- 1
-
On 20/03/2018 at 16:46, norsko said:
Very interesting! I have read several places that the Canton amp dont support impedance below 8 ohm, but that is not correct?
It would be interesting to see which speaker is connected to which chip.
There are 11 channels in use: 4 x door woofer, 4 x door tweeter, 2 x subwoofer and one for center speaker.
Maybe the chips for center and woofer channels already are bridged?
Dont think so. Please do wload the photos from drive and see it. There are 2 chips separated from the others with different power
-
Now will try with new front speakers. 80W at 3 ohm. I'm sure it will work properly.
Other thing is that frequency below 70 Hz in front speakers are absolutely useful -
1 hour ago, kogabe said:
Hi hitmn,
thanks for this info.
Accoding to the TDF8599CTH/N1 description, it should support bridge mode, I think (300Wx1 @3Ohm)
I was wondering if you had a chance to try it?
Thanks!
kogabe
Hi,
I'm using 2 speakers, getting power from separate channels. already 10 months no problems.
My speakers are : http://www.tb-speaker.com/products/w6-1139sif
Have a friend using 2 cone woofer : https://www.audison.eu/products/aps-10-d/
No problems at all.
Haven't tried bridge in prolonged use , but you can try it yourself. I have just tried if it will work, and it did. When I accidentally touch the wires the amp stopped. The amplifier has a built in protection. When activated, you must turn off car, and leave it until all the power are turned off by ECU. Then start again and will work.
Go ahead. It has all dummy protections, there is no way to burn it. -
Please delete this comment
-
You all need to do clutch adaptation with vcds interface
-
Installed 2 way component system - FOCAL PS 165 FX. After a lot of play with sound settings can say : The amp is clipping... so the speakers are too powerful for the amp.
In conclusion, all my fellow Bulgarians that are reading this and are going to take money from their customers for "know how" The maximum speaker wattage must be around 60W, not more for stock MIB 2 Amp.- 1
- 1
-
im in for more photos ... changing the front with focal at this point.
-
now ...
2 days ago bought Columbus head unit. removing standard bolero and placing Columbus made the sound in the car brutally better. So in my opinion reaching this point of view only changing the speaker will do the job.
Difference in the units (not CANTON AMP) is very big and the sound depth is definitely better.
And the big question ... to put 13 cm or 16.5 cm ? with adapters of course ...
-
Will try to power up some 60W-90W speakers with stock canton amp. But I'm pretty sure that THD will be greater, because the power cables of the MIB 2 amplifier under the seat in my opinion are just not enough. The perfect setup will be with additional amp under the passenger seat with some 15-20 mm2 cable and RMS for example 4x70-100. The signal must be taken on high level, because there is no other cheap option,other is optic and the amp is way more expensive. And this only if you want to get the most of this car music capabilities.
This all combined with Silent Coat on floor and doors. Total price around 1000 euro if using HERTZ amp and MilePro speakers.
Probably the project is getting mature in my head for now and I'm sure it is not for normal people -
On 9/26/2017 at 08:42, Jaco2k said:
You call bull**** to all the other contents of this thread and come in with all guns blazing, but...
...where are the much more essential measures about the depth for the front woofers with door windows down?
Also, if you are going to change woofers, I assume you change tweeters too - would be useful to know those sizes.
Of course that it is commendable to make efforts on behalf of the community, and for that you should be praised, but you should maybe have a more moderate language.
So ...
The depth of the front speakers to the glass is exactly as shown on the picture. The green cap i was using for more precise measurements- 2
-
Milion of people in this threat and only bul****s written ...
Canton is just a logo. Have a thread about canton amp inside. the unit its capable of handling 1000 wats and more its just been limited duo warranty ...
Spend time for you all ( because obviously you dont have enough to spend for others ) and these are front speakers on Octavia 3. Will change rear too but not now. After I get the work done will upload more pictures.
Cheers!
- 1
-
yes. in my opinion 350N is perfect force!
- 1
-
-
https://drive.google.com/open?id=0B_718rQ9DMtScnR3cnZzR0pRQ0U
This is on Google drive. Can't disappear
I found one of the semiconductors.
On the board there are 7 chips.
3 of them are 75610DAA 96R506 - No info on the web. maybe this http://pdf1.alldatasheet.net/datasheet-pdf/view/543737/ETC2/TDA75610DLV.html. it says 4 x 45 W, but no more info ...
2 of them are TDF8599CTH/N1 -Type Class D Output Type 1-Channel (Mono) or 2-Channel (Stereo) Max Output Power x Channels @ Load 300W x 1 @ 3 Ohm; 155W x 2 @ 6 Ohm Voltage - Supply 8 V ~ 48 V Features Depop, Differential Inputs, I²C, Mute, Short-Circuit and Thermal Protection, Standby Mounting Type Surface Mount Operating Temperature -40°C ~ 85°C (TA)
or on the other site :http://www.nxp.com/documents/leaflet/75017413.pdf
Can't read the other 2 chips.
-
hi guys,
I managed to open my amp because I want to use other speakers.
So made some pictures. Please administrator take some of them and put it on the forum, because the link will be available 5-10 days. I see that I can upload 10mb max, pictures are 250 mb.
Thanks in advance ! Waiting for some commends
http://dox.bg/files/dw?a=2c7edc9788
you must check the box of Canton amp.rar and push "Изтегли избраните".
If you want to upload them on some other site, please just say.- 1
- 2
-
Hi guys,
found the febi bilstein in ebay,
but can't find anything else.
I really need some help for those""The ball pins are 6mm x M10 and 8mm x M10, Ebay items 201561709396 and 401102290899 - although a slightly longer thread (at least 15mm of thread to allow for the thickness of the washer) would be better on the 8mm one. NB. first size is the thread, second size (M10) is the ball. The 8mm stud goes into the front bolt position of the hood hinge.
I got also got some 6mm and 8mm washers (the 6mm ones will need to be the "penny / repair" type to completely cover the hole in the wing mount, a standard washer is ok for the 8mm stud.""
-
I havent been able too achieve any progress. I have only 3 byte that can change. But none of the 3 enable offroad. Im starting to think that need coding, adaptation and something else ...
-
I think this is so called MirrorLink/SmartLink. If enabled it can copy your phone screen on the Bolero !
-
can't eat, can't sleep ... waiting for the scan ....
-
Hi,
my cousin has an audi a4, so ...
his side mirrors have an option that they fold when car is locked and are unfold only when key is in, not when car is unlocked ...is it possible to do with vcds with us ?
-
sure it can ! come on people .... there is no way someone hasnt get a scout with offroad
-
I want an update too
-
Hi.
Writing for first time.
I'm having a problem. I can't see anywhere 01 coding_light assist High_beam_assist in A5 module long coding. Where to find it ? If I go in Lcode2 menu I dont have any faling menus or texts... only tiks.
Have some Idea ... if somebody wants to use team viewer ...
Inside Canton Amplifier
in Skoda Octavia Mk III (2013 - 2020)
Posted
So after a lot of experiments ... this week I will put another pair of front speakers, that I'm sure would be best choice for this amp There are 28W/8 ohm Rated/ 56W Peak, and will not get any clipping ( I hope ). If all ok will put them in rear too ... Will use original housing for speakers, removing old cones ...
http://www.tb-speaker.com/products/w5-704d
Still using old subwoofers 2x50W/4ohm Rated/100W peak and no problem at all.