[Faulty steering wheel controls for Maxi dot]

I agree hmcn,

Mine did the same, worked for a month or so. Like a buffer is filled up and then it becomes very slow and at the end stops working. 

The wheel I purchased did have some other keys, so I reused my own keys like Lane Assist - no problem with that.

[Faulty steering wheel controls for Maxi dot]

Hi hmcn,

Changing the optocoupler didn't do the trick - sorry! It only worked for a month or so!

I found a steering wheel with defective leather and replaced the two pcb's - it has been  working like a charm for almost 3 month.

Something else is wrong with one of the pcb's (another component), I just hadn't had the time to investigate. 

So my advise is to find a steering wheel or new pcb's and replace it.

I hope you find a good and not too expensive solution.

 

[Faulty steering wheel controls for Maxi dot]

Just an update, if someone is still following this tread 🙂

I have now replaced the right optocoupler, the operation seems to have worked. I can now scroll without any delays or periodic function.

At the end it more and less stopped working, so I managed to find the optocoupler at something called RS Components 👍

It needs soldering, so make sure to have a good soldering iron.

I will update you all, if it stops working again! 

[Faulty steering wheel controls for Maxi dot]

Hi again 5k0d4,

I actually found a used steering wheel at a car wrecker; I replaced the PCB´s and it worked perfectly. Then I found the cleaning instructions of the sensor, and that worked as well. So, I returned the Steering wheel and my old PCB worked almost ½ year. 

 

If you do a search on: 5E0 919 719 F WHS - either on Google, Ebay or similar, you will find a replacement kit. 

 

Currently my scroll button works sometimes.

Good hunting.

[Faulty steering wheel controls for Maxi dot]

FYI: I managed to find the fault! It was the optocoupler which needed some cleaning

[Faulty steering wheel controls for Maxi dot]

Hi Milentije,

Did you managed to find the reason for the faulty scroll wheel on the right side for the Maxo Dot? As I now have the same fault! Now the car is not new anymore, so pretty sure Skoda will not accept it as a warranty case. But prefer to find an easy fix, so probably have to order a complete set of Steering wheel buttons: 5E0 919 719 A  

[5TA827566B rear-view camera problem]

Excelent, that makes absolute good sense. That is why I wasn't able to communicate with the controller - as I dont have the controller 

I am very grateful for the help 

[5TA827566B rear-view camera problem]

4 hours ago, jbastos said:

Isn't the 6C control module for the Highline model only?

 

Though I still didn't do it, the instructions I have to activate the lowline RVC are:

 

Controller 5C

Coding

Byte 19 - Activated bit 4

 

Controller 10 or 76

Coding

Byte 2 - Activate bit 4

 

 

Hi Jbastos,

I think the Lowline coding did the trick .

The camera picture came on, as soon as I put the car in reverse.

Thank you all for the good advice.

 

[5TA827566B rear-view camera problem]

Okay thanks, I will try Rosstech

 

[5TA827566B rear-view camera problem]

Okay, I get it now. But because I get the error message when entering 6C, I am not able to read out this code  Any ideas?

[5TA827566B rear-view camera problem]

Yes, same instruction. But not sure what this means: "6C (Manual tr.) > long coding: 0484020102002017000040"  (I have manual gear)

Otherwise all has been followed and confirmed.

 

[5TA827566B rear-view camera problem]

Yes, that the one. I just ordered it from: http://www.vwmodul.de/Lowline_Camera__Accessories/Camera/5TA827566B-MutatAlap.html

 

[5TA827566B rear-view camera problem]

Hi guys, 

I hope someone can help me!

I have just installed the original rear camera 5TA827566B (with washer). It had 3 wires, one short black wire for V-, one long red wire for V+ and one yellow midle length for activating the camera (connected to the reverse  light). Video cable connected to the radio unit (Pin 6 & 12).

Then I have done the coding as per instruction:

But I do not get any video signal up in the radio! When I go in and activate the "Car_Function_List_BAP_Gen2_VPS_oxoB", my sensors also disappear from the radio.

I have attached 2 pictures - "No response from Controller" failure code from VCDS.

I think it has to do with the Gateway connection (Pin 12 CAN LOW & pin 6 CAN High), but not 100% sure.

I hope someone here in the forum have an idea.

Thanks in advance :-)

 

[Skoda Octavia 3 - LED DRL dimming on turn signal]

Thank you very much PekoSI,

 

And Yes, I saw it on the Fabia.

[Skoda Octavia 3 - LED DRL dimming on turn signal]

Hi all,

 

I need some help with programming the LED light to dim, when the turn light is on -like Audi have  and the new Rapid.

So if there is someone who has a VCDS guide on how to program the LED light to dim (with Zenon) when the turn light is on, I will be very pleased.

Have tried the DRLs flash alternately with indicating, but this looks like as there is a problem with the light

 

Have search for it on here, but no results - found this on Youtube though:

https://www.youtube.com/watch?v=QkFoM9zCneo

 

Thanks in advance

/Kaare