ashS_skoda

Cold starts could be: Hpfp crank sensor Temp sensor Or carbon build up Read that a lot of them do this. Just the fast knocking until clutch is pressed down! Sent from my HTC One_M8 using Tapatalk

Had this knocking on cold idle from 2.0 TFSI vRS Octavia since iv had it, it stops when you put the clutch in, noticeable as the car seems to 'sound' like it runs quieter or smooth ect. Also the car is really rough and struggles to Start on cold, but has just this week had a full major service. Battery has been tested, no codes up or anything? So if read up about the rattle and have seen a post mention either the flywheel?!?! Or the release bearing and it get debriss on the crank sensor which effects cold starts because the magnets getting weakens? Or the clutch causes debriss one of the two lol? Any light on this? The cold starts are begin ing to be a pain, it starts, occasion it cuts out before then start right up, and takes a few seconds to wind over rough like a diesel :S And the noise is noticabke inside the cabin Sent from my HTC One_M8 using Tapatalk

That's the type of yellow I want, to what extent is the wrap? And how strong is it stone chip wise? Do you wash it like a normally 'metal' car ? Sent from my HTC One_M8 using Tapatalk

How much would I be looking at for a full wrap? Fancy a real strong yellow wrap Sent from my HTC One_M8 using Tapatalk

Yes mate please Sent from my HTC One_M8 using Tapatalk

Any guide on fitting? Sent from my HTC One_M8 using Tapatalk

2.0 TFSI intake is £185 ish ### in dollars can't remember. Delivery is £55 from USA! Where did everyone else get there's? Any cheaper way? Sent from my HTC One_M8 using Tapatalk

Does the facelift bumper and grill straight fit to non facelift!?!?!?!+!?!?!?!?! Sent from my HTC One_M8 using Tapatalk

Have a Octavia mate, and where'd Ben located?Sent from my HTC One_M8 using Tapatalk

I'm in Scarborough so where's the closest option for Shark? I'm looking for this 250bhp 400nm Sent from my HTC One_M8 using Tapatalk

No mate I have an Octavia tfsi vRS lol Sent from my HTC One_M8 using Tapatalk

Or raise in emmisions to fail Mot Sent from my HTC One_M8 using Tapatalk

Does blanking the PCV reduce gunk being produced? And does it cause anything negative like higher temps,idleing weird ect? Sent from my HTC One_M8 using Tapatalk

That said, New turbo fitted next day and that ripped off lol, was a fun 10 minutes tho Sent from my HTC One_M8 using Tapatalk

Lol I fitted a cheap boost controller on my old Saab Turbo because wasn't bothered about it. Fitted it, wound right open, got like 225bhp from like 150bhp and within 2 lengths down road big smoke out of exhaust hahaha, glowing turbo and manifold, inning she killed the turbo Sent from my HTC One_M8 using Tapatalk

+ Anyone got a link for a cheap catch tank to fit the TFSI? 300+ for the forge one :S Sent from my HTC One_M8 using Tapatalk

Just wondering with my 56 Tfsi vRS January 2007 registered, would it be recommended my PCV valve. Ring changed? Read that anything 2007 or older they do. If so which one do I get ? Do I get the one with breather hose? Anyone have a link for the best to to order? ++++ What's the situation on the PCV Blankings? Positives and Negatives? Sent from my HTC One_M8 using Tapatalk

How much did that cost you if you don't mind me asking? Was that complety standard bar stage 1 map? Need mine doing and these figures are what I'd be wanting Sent from my HTC One_M8 using Tapatalk

Wel I had a stripped out Saxo VTS which is the rallye in a girly frock, and that left the 1=4 Turbo corsa by quite a way, so maybe weight does help a lot haha, wel up to 100 ( private road that everyone seems to have that's 100000000 miles long lol) Sent from my HTC One_M8 using Tapatalk

Lol, yeah hopefully,I was thinking because of the weight but there also is like a 80bhp difference. Sent from my HTC One_M8 using Tapatalk

Sluggish vRS, are all Standard tfsi vRS like this, my mates 106 rallye with a GTi engine in it,can keep with me on my bumper up to 100? Also so can my mates 120bhp 1.4 Turbo cords black edition!? Will this divertor valve effect it majorly? Hoping a stage 1 map will help me leave them! God I hate saying that Sent from my HTC One_M8 using Tapatalk

You know how you got honeycomb style along the bottom grill? Realtime want mine like that! Sent from my HTC One_M8 using Tapatalk

How did u mesh all the way across the bottom mouth? Ance you done the upper grill to? Sent from my HTC One_M8 using Tapatalk

Turns out I tho k it says on receipt that wastegate valve or whatever they called it was sticking,think it would make much difference? Sent from my HTC One_M8 using Tapatalk

Coilpack, well it's in at the stealerships for invesergation at the price of £180for 2 hours!. I'm hoping it's the Divertor, because il fit it myself, and the coils,which also il do myself[emoji19], surely at 85,000 miles F.S.H it can't of killed the Turbo itself! Sent from my HTC One_M8 using Tapatalk