Hello!

Today I tried to connect to the car computer. I select auto scan function and I got this result:

VCDS Version: Release 10.6.1

Data version: 20100831

Saturday,25,September,2010,15:26:35:14583

Chassis Type: 7N0

Scan: 01 03 08 09 10 15 16 17 19 25 42 44 46 52 55 56 62 72 77

VIN: TMBGS61Z8B8015181

01-Engine -- Status: OK 0000

03-ABS Brakes -- Status: OK 0000

04-Steering Angle -- Status: OK 0000

08-Auto HVAC -- Status: OK 0000

09-Cent. Elect. -- Status: OK 0000

10-Park/Steer Assist -- Status: OK 0000

15-Airbags -- Status: OK 0000

16-Steering wheel -- Status: OK 0000

17-Instruments -- Status: OK 0000

19-CAN Gateway -- Status: OK 0000

25-Immobilizer -- Status: OK 0000

42-Door Elect, Driver -- Status: OK 0000

44-Steering Assist -- Status: OK 0000

46-Central Conv. -- Status: OK 0000

52-Door Elect, Pass. -- Status: OK 0000

55-Xenon Range -- Status: OK 0000

56-Radio -- Status: OK 0000

62-Door, Rear Left -- Status: OK 0000

72-Door, Rear Right -- Status: OK 0000

77-Telephone -- Status: OK 0000

-------------------------------------------------------------------------------

Address 01: Engine Labels: 03G-906-016-BKC.lbl

Part No SW: 03G 906 021 TB HW: 03G 906 021 AN

Component: R4 1,9l EDC G000SG 2047

Revision: --H11--- Serial number:

Coding: 0000071

Shop #: WSC 73430 790 00000

VCID: 72E1A79514DD

No fault code found.

Readiness: 0 0 0 0 0

-------------------------------------------------------------------------------

Address 03: ABS Brakes (J104) Labels: None

Part No SW: 1K0 907 379 AS HW: 1K0 907 379 AS

Component: ESP MK60EC1 H30 0105

Revision: 00H30001

Coding: 113B201C092300FF880C04EC901A0041340000

Shop #: WSC 73430 790 00000

VCID: 830F7251BB67

No fault code found.

-------------------------------------------------------------------------------

Address 08: Auto HVAC (J255) Labels: 5K0-907-044.clb

Part No SW: 3T0 907 044 AS HW: 3T0 907 044 AS

Component: Climatronic H15 0401

Revision: 00005001

Coding: 0000000002

Shop #: WSC 73430 790 00000

ASAM Dataset: EV_Climatronic A01006

ROD: EV_Climatronic_SK35.rod

VCID: 830F7251BB67

No fault code found.

-------------------------------------------------------------------------------

Address 09: Cent. Elect.

Cannot be reached

-------------------------------------------------------------------------------

Address 10: Park/Steer Assist (J446) Labels: 3C8-919-475.clb

Part No SW: 1Z0 919 475 C HW: 1Z0 919 475 A

Component: PARKHILFE 8K H06 0006

Revision: -------- Serial number: 66531021400614

Coding: 100001

Shop #: WSC 73430 790 00000

VCID: 4183385961FB

No fault code found.

.

.

.

.

.

.

-------------------------------------------------------------------------------

Address 46: Central Conv.

Cannot be reached

I solve problem to connect to addreess 09 so, that I turned off the car, then I locked the car and unlocked again and then I could connect to address 09: Cent. Elect.

But If I select address 46: Central Conv., I got several times an error "No response from controller".

And then I made auto-scan again and now I don't have address 46 on the list. I can't select this address any more.

What could be wrong?

Thanks.

I think I found what is wrong.

This address doesn't exist anymore. All functions from address 46 are now in address 09.

Can somebody confirm this?

I think I found what is wrong.

This address doesn't exist anymore. All functions from address 46 are now in address 09.

Can somebody confirm this?

You are correct!

BIG Nick

As stated by others, #46 is only acting as a virtual address with the new style BCMs. It's only listed in the installation list for compatibility reasons. You will see a similar behavior when it comes to the RNS310/RNS315 and Skoda Amundsen Radio Navigation System, they list #37 and #56 while they actually only talk via #37.

The actual BCMs have another goofy "feature". They do NOT answer via diagnostics if ANY door is locked. So just make sure you have all doors unlocked, then there should not be any issue.

HI Guys,

How are you doing there?

Unsure if I am writing on the right place here...Hope you guys can give me some useful advice on the following. I just got an OBDII VAG COM cable to my Octavia 1.9 Tdi Pd (new shape) (04 July). I have just installed the VAG COM software (3.11, 4.09, tried both of them so far.) everything looks alright, port works fine, cable compatibility test shows ok etc.. When I run the full autoscan only my Enginer ECU is found by the software, none of the others are (Steering wheel, ABS, Airbag). Message is NO response from the controller.)....

I would really appreciate any help or reply advice on this!

Thanks in advance to you all!

Tamas

Neither the hardware nor the software you use are compatible to that car. Communication is done via CAN, something your interface does not support.