BIG Nick

I changed mine to the one found in a lot of VW cars, Tiguan, T-Cross, Golf etc. Essentially as long as the release button is in the same place (front) it should fit. The one I got came from a T-Cross I think after some messing about I was able to get the gaiter off and move it over. Let me know if you want a picture as not sure I took any. Nick

I could be wrong but I believe it's integral to the headlight, so replacing it would mean stripping the headlight unit down. Happy to be proven wrong of course.

Hi All, After much searching the forum and Google I thought I'd ask the question, I recently pulled the door markers out which were replaced by the previous owner. They are the ones that project the "VRS" logo onto the floor, while they worked they weren't easily seen and when placing something in front of the projector I could see cracking in what was being projected. Attached are photos of the ones removed, I still have the original light but wanted to know what others had purchased like these that project the logo as I did quite like them albeit they were hard to make out. Thanks all.

I do it using the following SIM: https://www.amazon.co.uk/Three-Mobile-Pay-Broadband-Data-Black/dp/B01M3VJ2B2/ref=sr_1_3? Comes preloaded and works until the data expires or after 2yrs. As for the dongle I use one of the following: https://www.amazon.co.uk/gp/product/B07Z6JFHMQ There are cheaper dongles out there though.

@sutra so I had a crack at this over the weekend due to the nice weather, I was retrofitting an RVC. In the link below are pictures of what I needed to remove to remove the trim, you'll also see there is a join in the washer pipe right about where yours appears to be leaking (from your photo). I removed the rear boot trim that has the boot latch on it and the rear pillar trim, also the rear bench and the trim that goes over the wheel arch as this allowed for the trim to be pushed out of the way. There are 4 fixings, two with the fold out luggage hooks, one behind the rear pillar trim and the other where the rear shelf inserts. I also had to remove the two netting hooks and finally using a spline bit the lashing point right behind the rear seat, I pictured this separately as it has a cover hiding the bolt. You'll need to remove the rear luggage light as well, when I started to remove the trim piece I worked it from the rear over the lashing eye/loop fixed to the chassis. At this point I was able to reach in and disconnect the 12v socket, finally I had to lift the trim over where the seatbelt exits the trim. I wrapped the seatbelt round the rear seat that was folded down and this allowed me to move the trim far enough away to work comfortably, if you wanted to remove it completely you'd need to undo the seatbelt from the rear bench. Hope this helps, I think the fixing you were missing is hiding behind the rear pillar trim. https://photos.app.goo.gl/cEhR4N78kabEt3Au8

Morning All, I fell off of the list a while back but am happy to go back on. Have HEX-V2 in the Northampton area. Nick

I shall be fitting this one to mine in the next few weeks: https://www.cars-equipment.com/en/shop/tiguan/oem-highline-rvc-mqb-rear-view/ I originally bought it for my Tiguan but it turned out to be a bit of a lemon, when you compare the part numbers only the prefix changes based on the car. The below link is for the Octavia 5E https://www.cars-equipment.com/en/shop/rear-view-cameras-3/oem-highline-rvc-rear-view-camera-3/ As you can see from the kit the loom does split in the boot lid, camera feed and then power and canbus cables. You might be able to get away with the following depending on what you have already. https://www.cars-equipment.com/en/shop/rear-view-cameras-3/oem-5q0980568b-rear-view-highline-camera/

I might have a go at mine this weekend if the rain holds off. I have the variable boot floor in mine and the Canton amp, whether that makes it harder or easier I don't know! If I have any success I to will let you know.

Morning, Did you have any success with removing this trim at all? I have a rear reversing camera I want to fit but when doing my dashcam for the rear I found this piece of trim to put up a fair fight, I removed all the screws I could find which look to be the same as you. Thanks, Nick

Did you manage any pictures for those of us with the EGR cooler? Cheers Nick

My turbo on my PD140 (09 Plate) is being painful and the vacuum/actuator appears to get stuck making the car howl like a banshee. There appears to be a lot in the way from above on the FL so will go from underneath. Can I ask is the turbo easy to access from underneath as tbh I've never looked Cheers Nick

If your friend is interested in doing another do let me know

So will you be sharing how you did this? Looks interesting.

Didn't have to change anything on mine, although I did buy the 50w versions which I think would draw more power.

I got so bored of mine (is an 09) I went and bought these bad boys: http://www.amazon.co.uk/gp/product/B00BTDTIKK/ref=oh_details_o03_s00_i00?ie=UTF8&psc=1 Pricey but bought them through the company I work for and wrote them off as expenses. It's either that or attach normal bulbs in a piggy back fashion. Nick