2014 yeti elegance 140 trailer retrofit (1K)

Followers

14 June, 201411 yr

looking for advice with coding of 2014 Yeti elegance FL Outdoor with towbar prep and EEA63002E4 single electrics and witter detachable flange towbar.

Installation all gone smoothly .Coding carried out as per Ross-Tech retrofit instructions for Yeti 5L....VCDS version 12.12.2.0

Updated Gateway (J533/#19

Updated trailer module J345/#69

Update to brake electronics J104/#03 not required as MK60EC1 is installed and activation not required

Update to engine control module (J623/#01) coding amended for trailer with long coding assist

all ok up to this point

update to parking air (J446/#76 or parking aid (J446/#10) these address not found but J791/#10 is my Yeti address for park assist

selected this module

selected coding 07

selected long code helper

no bits indicated for trailer

enetred adaption

no details for trailer coding

can anyone advise where I am going wrong

trailer lights all working but no trailed indicated on bolero and all rear sensors sounding with ignition on and reverse gear selected

log files attached before and after coding attempt

thanks for any advice

Log-FD14 TDZ-TMBMD75L5E6045201-all coding carried out.txt

Log-FD14 TDZ-TMBMD75L5E6045201-trailer module before coding.txt

3 weeks later...

2 July, 201411 yr

Author

looking for advice with coding of 2014 Yeti elegance FL Outdoor with towbar prep and EEA63002E4 single electrics and witter detachable flange towbar.

Installation all gone smoothly .Coding carried out as per Ross-Tech retrofit instructions for Yeti 5L....VCDS version 12.12.2.0

Updated Gateway (J533/#19

Updated trailer module J345/#69

Update to brake electronics J104/#03 not required as MK60EC1 is installed and activation not required

Update to engine control module (J623/#01) coding amended for trailer with long coding assist

all ok up to this point

update to parking air (J446/#76 or parking aid (J446/#10) these address not found but J791/#10 is my Yeti address for park assist

selected this module

selected coding 07

selected long code helper

no bits indicated for trailer

enetred adaption

no details for trailer coding

can anyone advise where I am going wrong

trailer lights all working but no trailed indicated on bolero and all rear sensors sounding with ignition on and reverse gear selected

log files attached before and after coding attempt

thanks for any advice

all now working,with trailer connected image of trailer displayed on bolero with rear sensors disabled.

Solved by downloading vcds beta software,all options for trailer activation in park assist j791#10 are in the beta vesion.....

Gordony

Create an account or sign in to comment

Followers

Go to topic listing

No registered users viewing this page.

Announcements

About BRISKODA

BRISKODA is for the sharing of information on ŠKODA. Founded for all motoring enthusiasts, it's free to join and use. We have members from all over the world.

Our Guidelines.
Search the Site.
Explore the Forums.
Gaze into the Gallery.
Make a date, the Calendar.
Classic, custom or modified car insurance!
Please be respectful when posting.

See all Subscription Plans

Goodbye to my Octavia MK3
Hellos and Goodbyes

Goodbye to my Octavia MK3

paulski · 1 minute ago1 min

Been here a little under 7 years. Great forum, I'm sure I'll hang around still but I've moved my octy on now for a VW Tiguan. The Octavia was a cracking car, reliable too. I took it from 47k to 120k miles, and it really didn't disappoint. The only issue it had was the heater matrix, which I had replaced eventually after freezing hands in winter!! It will pass to a new owner with full service history (Independent Vasstechnik in Eastbourne who are just great with all VW group cars). I've left
- 0 replies
- 0 views
paulski

1 minute ago1 min

paulski

1 minute ago1 min
My Mk1 Fabia SE
Skoda Fabia Mk1 (1999-2007)

My Mk1 Fabia SE

bendutton · 8 May8 May

Anyone on here got some information about my SE, i noticed above the driver side headlight that there was a sticker previously there of the website just wondering if anyone can tell me anything about it, cars been great so far but needs a new camshaft so upgrading to the SDI
- 8 replies
- 508 views
bendutton

8 May8 May

wilsonian

16 minutes ago16 min
What have you done to your Superb III today?
Skoda Superb Mk3 (2015 - 2023)

What have you done to your Superb III today?

boydeee · 25 August, 20187 yr

There was a similar thread on the Golf GTI site I used to be on and I found it really interesting to see what other's had been up to. My car is due to be built this week (34) so I am counting down the days until I finally get it! So what have you lot been up to?
- 5,331 replies
- 614,942 views
boydeee

25 August, 20187 yr

Binx1310

18 minutes ago18 min
remove the engine splash shield underneath the front bumper
Skoda Octavia Mk3 (2013 - 2020)

remove the engine splash shield underneath the front bumper

Rickssokda · Wednesday at 19:373 days

Hi all, I'm trying to get at the lower radiator hose in my 2016 Octavia. I've looked on google and found that I should remove the seven t25 screws. 5 on the bumper splash shield and one on each side connected to the fender. The shield seems loose, but it won't come off and I don't want to try and pry it too much as I'm concerned that I'll crack it. Can someone tell me what additional screws, or maybe clips, need to be removed to get this off? many thanks for all info
- 4 replies
- 146 views
Rickssokda

Wednesday at 19:373 days

Rickssokda

19 minutes ago19 min
3V0827566N pinout DIY wiring mistake. Burned rear camera by sending 12V to CAN High
Skoda Superb Mk3 (2015 - 2023)

3V0827566N pinout DIY wiring mistake. Burned rear camera by sending 12V to CAN High

Raiko84 · 32 minutes ago32 min

Hello everyone I decided to update my 2014 Skoda Octavia to a newer age. First changed the MIB1 to MIB2, and then decided to add a rear view camera (there are other projects on the way like MFK1 to MFK2). I want to tell the story so someone else does not make the same mistakes I did. My Skoda never had a camera, so I bought one from a scrapyard, a 3V0827566N without the wiring harness, it scrapped with the body. But since I had no wiring I needed a harness, contacted Skoda Parts, got no concre
- 0 replies
- 26 views
Raiko84

32 minutes ago32 min

Raiko84

32 minutes ago32 min

2014 yeti elegance 140 trailer retrofit (1K)

Featured Replies

Create an account or sign in to comment

Recently Browsing 0

About BRISKODA

Available Subscriptions

FREEDOM Lite

FREEDOM

Recent Topics

Goodbye to my Octavia MK3

My Mk1 Fabia SE

What have you done to your Superb III today?

remove the engine splash shield underneath the front bumper

3V0827566N pinout DIY wiring mistake. Burned rear camera by sending 12V to CAN High

Important Information

Account

Navigation

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)