Guys, has anyone else got one of these polished jom adjustable ones

Ive fitted mine and ive noticed its slightly pushing the bonnet up on the passenger side?

Im going to contact where i got it to see what they say but thought id aslo ask you guys

I've got a ABD racing strut brace and that rubs on the bonnet bracing but it doesn't seem to lift it,does yours brace look higher on that side and can u see where its rubing?

It is slightly higher that side mate, the foot is tight down, its somewhere over the maf id say rite over that side. Thinking put a towel on it and a bit of a tonk to try bend it down but given its a strut brace im thinking it wont want too.... Plus i dont want to break the weld

I only noticed it cos im abit ott so was running hand up the gap when was shut

Yo pal i fitted one of these last weekend and have had the same problem. The only thing i can think of doing is raising the bonnet to try and clear it theres hardly anything in it, but so such a pain after all the effort to fit it. Wats ur plans?

Sent from my GT-I9100 using Tapatalk

Pics??

i have 1 thats iv had on my a3 and bora. not fitted to the vrs yet. interesting.

I'll get some pics up, ive tightend it so it bows down pulling it down abit, but its still up a little

Ive got holes in the bloody car now so it cant come off

Im abit gutted to say the least, i wrapped in a tshirt and beat **** out it to so it down as far as i can

Hmmmm

This was 1st on

Then tightend so bends the side down a tad

Then snapped the screwdriver is was winding it with so thats how it is at mo lol

i would say your heat sheild has somthing to do with that!

And to **** me off more, i trimmed out a slot in my jabba induction kit shield that took fooking ages

So it has to stay.... Maybe abit mire of a play about, or as said lift bonnet both side a smidge

Hmm

Hmm

Hmm

None the less i now know why indeed twere £32

It slots down in the groove ive cut out on the shield mate, i did slide the rubber sleeve back along which is abit chunky so i'll trim it off and try it

But it does still move if you pull it so its not trapped

Nothing to loose

i just been down to look at mine, laid the brace on the car and closed the bonnet no problem... Strange.

Just my luck..... I'll look into it tomaro

Might be worth a try just taking the rubber seal from heat sheild off again and try

Not having much luck lately :(

chin up dude, its prob somthing really simple.

I hope so bud, i'll peek again tomaro

Its another day :( just really not getting on too good lately

One bummer after another

Car, family, health, job .... Damit

AAAAAAAARRRRGHHHHH

i would say your heat sheild has somthing to do with that!

I concur, I dont have a heat shield and mine seems to sit ok.

i just been down to look at mine, laid the brace on the car and closed the bonnet no problem... Strange.

Think I am going to look at mine again to see how my bonnet sits. thought my bonnet was lifted slightly, when run fingers down side, but i have had a front end smack whcih i was wondering if it was to do with that, as bonnet sits fine at top where brace is and bottom where catch is.... just part way up it seems to be a bit raised.

But interesting.

Im rite on guessing your all talking about the jabba induction kit sheild when on about heat sheild yeah ???

Im rite on guessing your all talking about the jabba induction kit sheild when on about heat sheild yeah ???

yes mate.

I'll double check it, i trimmed a nice neat cut out the brace sits in but none the less i shall sooner double check and rule it out

i wont two of them polished lifters for my roomster jamy person more info thanks pete

Those lifters were a bargin lol

I got them off a awesome briskie that sold them for a mere £20 they dont catch or anything mate

I have no idea on the make :( i think thst superskoda site do some but are lots of wonga, i'll see what i can find out mate

Rite....... You little gitbag

One of these

One if these

That goes there

This on that

Repeat

Bonnet shuts fine

******* thing !!!!!!!

Hulk smash

Spoke to dave...... His on close lookibg did the same

Just to let folk know

Thats 3 that have done it niw it seems

Although i think i have got mine sorted to the level of ok-ness ...... With the correct tools

Will see how it goes now ...... If need be it will get another talking too

hmmm.. im interested at to why mine sits ok. its a couple years old now so mite be slightly different. glad you got to the bottom of it tho dude.

Yeah mate , bit of a talk to it and its gine enough lol the other side of the bonnet is abit low which dont help

I think they built it on a friday afternoon lol not touching it tho or who knows what i'll do to it

Unless i put it out abit when i undid bonnet for lifters

Hmmmmmm doh

Mines got a straight cut on the one side too lol as if they made that foot out of a off cut