951 OCC Info Page

Bracket is shown in pic above but without the bracket you would have to mount it by a big jubilee clip.

Saikou Michi Home Page

We can probably order some hose off him but if we get hit by customs i think it would work out dearer.

I will look into some black oil resistant hose from Arco and let you know.

you will need 2metres of 19mm oil resistant silicone ( if not pipe will corrode and colour change)

also a 19mm t piece

and 7 19mm jubilee clips thats it

jobs a good un will post pick of mine in a minute

you will need 2metres of 19mm oil resistant silicone ( if not pipe will corrode and colour change)

also a 19mm t piece

and 7 19mm jubilee clips thats it

jobs a good un will post pick of mine in a minute

Nice one, thanks for the info.That is well fitted there mate. Can you let me know pipe lengths and where you got them or was it same place as the OCC.

Jay is it worth doing a group buy on hose's and the T pieces then we can all cut them to length.

the hose was 2 metres of samco silicone oil resistant..i cut to size

and the T piece was made for me by baileys for about £10

the hose was 2 metres of samco silicone oil resistant..i cut to size

and the T piece was made for me by baileys for about £10

Cheers, sorry you did mention 2 metres already. I was refering to the actual lengths you cut to size. But I guess that is pretty simple when you weight up where the OCC is to be fitted and the T piece sorted..

i would cut it to length when you have the catch tank etc fitted where you want

can take a few more pics if you wish to see the running of the lower hose etc etc

i would cut it to length when you have the catch tank etc fitted where you want

can take a few more pics if you wish to see the running of the lower hose etc etc

Think I have it covered but would be nice to see where the lower pipe from the T piece goes. I have seen a few peeps use a Y pipe instead of a T peice and just fit the Silicon pipe directly over the original Plastic Breather pipe by the side of cam cover.

Would like to see where the end of the lower pipe goes to really make sure I have it sorted. Cheers

Think I have it covered but would be nice to see where the lower pipe from the T piece goes. I have seen a few peeps use a Y pipe instead of a T peice and just fit the Silicon pipe directly over the original Plastic Breather pipe by the side of cam cover.

Would like to see where the end of the lower pipe goes to really make sure I have it sorted. Cheers

Me too

will get a pic up tomoz as im at work now

it replaces the pipe that some attach the silicone to the one that goes under the inlet manni. i replaced it with silicone because mine was completley perished

very easy and worth doing

i would also advise at the same time as doing this remove your intercooler and clean oil out aswell as you intake hoses

Have you seen this link?

1.8t - PCV simplification and catch can installation - uk-mkivs

The sludge that came out of the engine :eek:

will get a pic up tomoz as im at work now

it replaces the pipe that some attach the silicone to the one that goes under the inlet manni. i replaced it with silicone because mine was completley perished

very easy and worth doing

i would also advise at the same time as doing this remove your intercooler and clean oil out aswell as you intake hoses

Go outside and take a photo you lazy sod!:P:D

Money grabbing sod,to pay for more mods.

Go outside and take a photo you lazy sod!:P:D

Money grabbing sod,to pay for more mods.

lol i havent got my camera or i would have :P

far to busy anyway porting and polishing + smoothing outershell of my spare inlet mannifold

p.s that pic with the **** in was just like my pipe that was split on the lower pipe thats why this is one of the best mods to do imo and why it should be 19mm all the way through and not drop down to smaller sizes like other catch tanks

i replaced the upper pipe to Y piece shown on the right of the pic:thumbup:

Looks like it goes inside the T piece at the bottom - did you have to use a joining piece?

yes mate i actually used a 19mm small joiner and pushed it in no probs

I didn't get any payment details over the weekend... Any news yet?

Sent everyone a PM as just waiting on email form supplier 1st.

Sent everyone a PM as just waiting on email form supplier 1st.

I've emailed Mr. Saikou with my order, just waiting to hear back from him now. Dunno what the time difference is, but I'm guessing it's early morning there now...

I've emailed Mr. Saikou with my order, just waiting to hear back from him now. Dunno what the time difference is, but I'm guessing it's early morning there now...

Did you get my last PM regarding payment?

Yup

Yup

Good PM transaction after you have paid.

Paid so far

Jaymd

Bertee

Have I missed out?! :(

If I have, if anyone drops out, I'd fill their place

Good PM transaction after you have paid.

Paid so far

Jaymd

Bertee

How did you manage to pay so quick! Nobody has emailed me back yet. Would be alot easier if they had an online payment thingy

How did you manage to pay so quick! Nobody has emailed me back yet. Would be alot easier if they had an online payment thingy

You pay by paypal to the email address i sent you.

You pay by paypal to the email address i sent you.

Paypal? I don't have paypal! I just told him I want to pay by Visa card, and what details does he need.

Is it easy to set up a paypal account then? I only ever use ebay to find stuff or check prices, I'm more of a cash person!