Hello dears, can the 565 920 790 D cockpit fit well Kodiaq 05/2019 Style ?  Thanks 

This is the third thread that you have started on this same topic. 

 

D will not work.

C will not work.

 

You need 565920790, 565920790a, or 56G920790

 

I do not know what the difference is between the first two. The third one is China part number. 

 

Anything newer then these will not work. Please stop asking, it won't change! 

Thanks its clear. 

I put 56G920790 in my car, it's fine. 

Hello,

 

I have a Kodiaq built in 2017 and the China VC (56G 920 790) installed, it works so far but my VC cannot display the navigation view. See picture (Optical cable was used).

There are a few users here that have installed this VC (56G 920 790), can you show me your coding?

@ApertureScan you advise @ibu400 if it's possible to get his MIB2 headunit to send maps to his new VC please? His headunit is 3V0 035 021 D 

Thanks. 

 

On 16/01/2024 at 20:46, ibu400 said:

Hello,

 

I have a Kodiaq built in 2017 and the China VC (56G 920 790) installed, it works so far but my VC cannot display the navigation view. See picture (Optical cable was used).

There are a few users here that have installed this VC (56G 920 790), can you show me your coding?

You’ll need to post an adaptation map of 5F so I can see the changes you have made.

 

also I assume you have turned the coding bit for MOST on?

Hello, 

Just install 56G920790 on my Kodiaq Style 2019 as picture attached. One thing missed for the screen view i cant show the one big counter view. Any idea? And i dont control to customer the choice of each view counters? What other missed to feet that? Thanks

On 31/01/2024 at 19:10, sindibade said:

Hello, 

Just install 56G920790 on my Kodiaq Style 2019 as picture attached. One thing missed for the screen view i cant show the one big counter view. Any idea? And i dont control to customer the choice of each view counters? What other missed to feet that? Thanks

Adaptation in 17 called 'Sport' enable it, that will give the sport single dial cluster.

To adjust the display for both dial centre pieces it is done through the infotainment vehicle and scroll side ways to the next menu called AID - this needs enabling in the 5F adaptations also.

On 25/01/2024 at 06:54, ApertureS said:

You’ll need to post an adaptation map of 5F so I can see the changes you have made.

 

also I assume you have turned the coding bit for MOST on?

@Freedom thats my 5F, What do you need exactly?

Yes, the bit is on:

ENG122230-ENG142097-Dashboard_Display_Configuration-ability_switch_nav_maps,OFF
ENG122230-ENG122343-Dashboard_Display_Configuration-call_picture,On
ENG122230-ENG122341-Dashboard_Display_Configuration-coverart,On
ENG122230-ENG122340-Dashboard_Display_Configuration-crossroad_detail_map_compression_mode,H264
ENG122230-ENG122344-Dashboard_Display_Configuration-crossroad_detail_map_resolution,resolution_3
ENG122230-ENG127006-Dashboard_Display_Configuration-crossroad_detail_map_transmission_mode,MOST_streaming
ENG122230-ENG142153-Dashboard_Display_Configuration-dynamic_icon,0
ENG122230-ENG127501-Dashboard_Display_Configuration-fastlist_most,On
ENG122230-ENG122338-Dashboard_Display_Configuration-navigation_map_compression_mode,H264
ENG122230-ENG122339-Dashboard_Display_Configuration-navigation_map_resolution,resolution_3
ENG122230-ENG127005-Dashboard_Display_Configuration-navigation_map_transmission_mode,MOST_streaming
ENG122230-ENG122342-Dashboard_Display_Configuration-stationart,On

 

thank you for your help

Thanks done

On 25/01/2024 at 06:54, ApertureS said:

You’ll need to post an adaptation map of 5F so I can see the changes you have made.

 

also I assume you have turned the coding bit for MOST on?

Here again 5F and 17 (KOMBI):

 

Adresse 5F: Informationselek. I (J794)       Labeldatei:| 3V0-035-MIB-HGH2.clb
   Teilenummer SW: 3V0 035 021 D    HW: 3V0 035 021
   Bauteil: MU-H-LND-EU   H50 1433  
   Seriennummer: A674D0HS025034
   Codierung: 03231601FF0000005111120100880A332F0300C4012081009E
   Betriebsnr.: WSC 131071 1023 2097151
   ASAM Datensatz: EV_MUHig4CGen2HBAS 001001
   ROD: EV_MUHig4CGen2HBAS_VW37.rod
   VCID: 2855A56253F3F2C662-807C

   Anzeige- und Bedienungseinheit 1 für Informationselektronik:
   Subsystem 1 - Teilenummer SW: 565 919 605 B    HW: 565 919 605 B
   Bauteil: ABT_Std-2_Nav  H35 8084
   Seriennummer: SKZ6ZHT1072014      

   Datenträger:
   Subsystem 2 - Teilenummer SW: V03 959 820 ML    HW: -----------
   Bauteil: ECE 2024  --- 0350
   Seriennummer: --------------------

   Compact Disc Datenbank:
   Subsystem 3 - Teilenummer SW: V03 959 800 EG    HW: -----------
   Bauteil: Gracenote2---  --- 1013
   Seriennummer: --------------------

Kein(e) Fehlercode(s) gefunden.

 

and

Adresse 17: Schalttafeleinsatz (J285)       Labeldatei:* Keine-SRI3
   Teilenummer SW: 56G 920 790     HW: 56G 920 790
   Bauteil: KOMBI         104 1702  
   Codierung: 05AC0019EF8C00080088770B3001000800000000
   Betriebsnr.: WSC 00046 000 00000
   ASAM Datensatz: EV_DashBoardVDDMQBA0 001026
   ROD: EV_DashBoardVDDMQBA0_VW37.rod
   VCID: 6DDB9476BC9117EED1-8038

Kein(e) Fehlercode(s) gefunden.

 

@Freedom it would be great if you could help me

Youll have to tag @ApertureS not @Freedom - Freedom is the forum rank 😛

 

But as for your fault :

Do you get any radio station icons show up on the AID or any photos of callers - they should match the ones displayed on the MIB.

Do you have the canton sound system or any other bits on the MOST network?

On 16/02/2024 at 22:24, ApertureS said:

Youll have to tag @ApertureS not @Freedom - Freedom is the forum rank 😛

 

But as for your fault :

Do you get any radio station icons show up on the AID or any photos of callers - they should match the ones displayed on the MIB.

Do you have the canton sound system or any other bits on the MOST network?

 

@ApertureS oh sorry, about that 🙈 Hopefully now I have linked you correctly

 

To your answer, no, no station logos etc. are displayed and there is no Canton etc. installed

 

 

I hope you can help me

 

9 hours ago, ibu400 said:

 

@ApertureS oh sorry, about that 🙈 Hopefully now I have linked you correctly

 

To your answer, no, no station logos etc. are displayed and there is no Canton etc. installed

 

 

I hope you can help me

 

You’ll have an issue with the MOST network then, either connection or coding.

 

are you sure the direction or the most bus is correct? As it needs to run in a loop.

 

and is most enabled in the instrument cluster coding too?