I recieved them

I tested them, working fine.

27 minutes ago, Giannis20 said:

I recieved them

I tested them, working fine.

Looks great 👍🏼

Nice !

Well, i did the installation. One hour for both sides.

4 minutes ago, Giannis20 said:

Well, i did the installation. One hour for both sides.

Looks great

Can you make a longer video using the parking lights, please

On 17/04/2025 at 09:59, Giannis20 said:

I recieved them

I tested them, working fine.

Hello

Works ok? Does it any light (error light) on the panel (virtual cockpit)?

New turn lights, working fine, no error messages on dashboard.

The light intensity is better than the OEM lights.

On 20/04/2025 at 18:58, Giannis20 said:

New turn lights, working fine, no error messages on dashboard.

The light intensity is better than the OEM lights.

Great work Giannis! I sealed the cable and will install mine soon! They look amazing!

Was the installation hard?

Hi,

thanks.

There is no hard step on the installation.

Here some photos from the procedure, i t might help someone.

Mirror removal:

2 screws

Clips for the upper part.

Front frame removal

l

Edited 22 April, 20251 yr by Giannis20

Ok, mines are on as well. Important! From the inside you miss the blinker on the outer corner of the mirror. @Giannis20 can you confirm as well?

I would say it's the way it works.

3 hours ago, Mario_Delgado said:

Ok, mines are on as well. Important! From the inside you miss the blinker on the outer corner of the mirror. @Giannis20 can you confirm as well?

I would say it's the way it works.

Yes you are right. It is common on those dynamic turn lights. I have installed a similar one in my other car, a VW Polo, and it is also almost invisible there.

17 hours ago, Giannis20 said:

Hi,

thanks.

There is no hard step on the installation.

Here some photos from the procedure, i t might help someone.

Mirror removal:

2 screws

Clips for the upper part.

Front frame removal

l

Thank you for the pictures! Next weekend i will install mind :)

Thanks a lot for the feedback @Giannis20 . I did a full scan and I can confirm that it doesn't trigger any error in control units.

Edited 23 April, 20251 yr by Mario_Delgado

On 22/04/2025 at 11:36, Lukas_2611 said:

Great work Giannis! I sealed the cable and will install mine soon! They look amazing!

Was the installation hard?

Hello @Lukas_2611 ,

What product did you use to seal the cables?

Something similar to:

Liquid Insulating Tape Repair Rubber

https://a.aliexpress.com/_Eut4iWW

Thank you

10 hours ago, djmartzian said:

Hello @Lukas_2611 ,

What product did you use to seal the cables?

Something similar to:

Liquid Insulating Tape Repair Rubber

https://a.aliexpress.com/_Eut4iWW

Thank you

Hi,

i used a black silicone. You just need to make sure that no moisture can get inside. So I think silicone can do this job very well.

20 hours ago, djmartzian said:

Hello @Lukas_2611 ,

What product did you use to seal the cables?

Something similar to:

Liquid Insulating Tape Repair Rubber

https://a.aliexpress.com/_Eut4iWW

Thank you

I used glue for cars.. like for the window or body.. i dont know the name in english..

https://amzn.eu/d/jfcbc70

On 24/04/2025 at 08:44, Giannis20 said:

Hi,

i used a black silicone. You just need to make sure that no moisture can get inside. So I think silicone can do this job very well.

How did you disassemble the unit without breaking? I think its really tough.. maybe i am doing something wrong..

On 26/04/2025 at 17:54, Lukas_2611 said:

How did you disassemble the unit without breaking? I think its really tough.. maybe i am doing something wrong..

Please be more specific. I don't understand which part do you mean.

14 minutes ago, Giannis20 said:

Please be more specific. I don't understand which part do you mean.

I mean to dissamble the indicator unit out of the cover..

yes I understand.

It is a little difficult, because it is fastened in 3 places.

A little patience, start from the inner fastening, it comes out easily, the difficult part is the edge, that's where you need to be careful because the protrusion can break.

Edited 27 April, 20251 yr by Giannis20

12 minutes ago, Giannis20 said:

yes I understand.

It is a little difficult, because it is fastened in 3 places.

A little patience, start from the inner fastening, it comes out easily, the difficult part is the edge, that's where you need to be careful because the protrusion can break.

I broke this little part 4x times.. on the originals and on the new ones.. xD ..

So I ordered new running lights... they are on the way..

The running light units where also a little damaged on the edge.. so I hope the new ones are better..

I also recognized that the E sign was wrongly made.. so how its called.. upside down? Are yours in the right position?

Thanks for the pic.. I started at the edge.. so on the outer part.. maybe that was the mistake..

Edited 27 April, 20251 yr by Lukas_2611

@Giannis20 is your E Sign in the correct position? :)

6 hours ago, Lukas_2611 said:

@Giannis20 is your E Sign in the correct position? :)

Sorry, i didn't understand what you mean.

19 hours ago, Giannis20 said:

Sorry, i didn't understand what you mean.

There is a sign on the light unit.. 015 E 12345 or something like that. On my running lights it was upside down.. so when installed wrong pposition

ΟΚ, you mean the E sign

It's upside down, as you can see in the photo. But they work as they should.