Hi. I have installed all the parts now and done the coding I believe is right, but fear I may have a couple of issues.

It looks like I might have a wiring issue with a couple of sensors showing a short. I have extended the loom so may be my dodgy wiring.

Also looks like it’s looking for rear cross traffic alert and ev motor. So I think dataset is wrong on module. (It was from a 1.4 hybrid) not sure if this can recoded or I need a different module.

Any help gratefully received. I use carscanner rather than vcds hence the difference in format.

10. Parking Assistant 2

Application data identification: W5

VAG Part number: 5QA919294G

Software version: 0061

ECU manufacturing date (ASCII): &

ECU serial number: 00015005832014754118

Hardware Part number: 5QA919294

System supplier ECU hardware number: 00015005832014754118

System designation: PDC 8 Kanal

Calibration date (ASCII): 000101

ASAM/ODX: EV_EPHVA18AU3700000

Hardware version: H08

ASAM/ODX version: 009046

FAZIT Identification: ATW-00126.05.20ED020881

Parameter set part number: V03935310QN

Parameter set version: 0001

System abbreviation: J446

ECU manufacturing date (HEX): 200526

Date of last adaptation: 000101

Date of last coding: 200617

Diagnostic mode: 01

Parametrization date: 200617

Long Coding: 1471055851

--------------------

17. Dashboard

Application data identification: --------------------------

VAG Part number: 3V0920941

Software version: 6422

ECU manufacturing date (ASCII): 151119

VIN: TMBKJ7NP9G7041006

Hardware Part number: 3V0920941

System supplier ECU hardware number: A2C945862040000_D2255

System supplier ECU software number: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

System designation: KOMBI

Calibration date (ASCII): &)

ASAM/ODX: EV_DashBoardVDDMQBAB

Hardware version: 213

ASAM/ODX version: 009046

FAZIT Identification: VD1-04819.11.1573958407

Parameter set part number: -----------

Parameter set version: ----

System abbreviation: J285

ECU manufacturing date (HEX): 151119

Date of last adaptation: 260329

Date of last coding: 260902

Diagnostic mode: 03

Parametrization date: 000101

Long Coding: 27A5090A2F90A60001887A011000000000000000

--------------------

Car Scanner ELM OBD2

Version: 2.1.46/2.1.46/iOS

DTC report

Connection profile: Skoda MQB, PQ26: Diesel DPF var.1 [EA288]Date: 9/2/2026 12:27:11 PM

VIN: TMBKJ7NP9G70XXXXX

============================

OBD-II

No DTC found.

============================

10. Parking Assistant 210. Parking Assistant 2

DTCs: 4

----------------------------

1111828 [0x10F714]

B10F714: Left front park assist sensor, Open circuit/short circuit to ground

Geber für Einparkhilfe vorne links-G255 - Unterbrechung/Kurzschluss Masse

Status bits: 1

Priority: 3

Frequency: 2

Unlearning index: 86

Odometer: 213832 km

Date, time: 2026.09.02 12:13:58

Status: Test failed, Confirmed

----------------------------

1112340 [0x10F914]

B10F914: Right front center parking aid sensor, Open circuit/short circuit to ground (GND)

Geber für Einparkhilfe vorne rechts mitte-G253 - Unterbrechung/Kurzschluss Masse

Status bits: 1

Priority: 3

Frequency: 2

Unlearning index: 86

Odometer: 213832 km

Date, time: 2026.09.02 12:13:58

Status: Test failed, Confirmed

----------------------------

12656928 [0xC12120]

U112100: Databus missing message

Motorsteuergerät - Motor_EV_01 - kein Signal/keine Kommunikation

Status bits: 1

Priority: 6

Frequency: 1

Unlearning index: 86

Odometer: 213832 km

Date, time: 2026.09.02 12:13:38

Status: Test failed, Confirmed

----------------------------

13639168 [0xD01E00]

U112100: Databus missing message

Steuergerät für Rear Cross Traffic Alert - RCTA_01 - kein Signal / keine Kommunikation

Status bits: 1

Priority: 6

Frequency: 5

Unlearning index: 86

Odometer: 213832 km

Date, time: 2026.09.02 12:13:38

Status: Test failed, Confirmed

Edited Wednesday at 13:552 days by Binx1310

I have ordered a 5QA919294B from a Diesel in the hope that the dataset is plug and play!

You hab vas dongle?(

44 minutes ago, Cairus said:

You hab vas dongle?(

No unfortunately not.

Is it a new dataset required? There is a guy with odis at a local garage that I can go to if needed. Perhaps you could connect through him or provide dataset for him to load.

I will try the other module I have ordered from eBay and if not will have to look at getting it trying the above!

Some progress made. I thought while I wait for the new module come I would do some fault finding on the sensors. Luckily I started fault finding at the plug end. Starting by checking pinout. It would seem my eyes are not very good at distinguishing between 10 and 18 and I’d managed to pin one side of the plug backwards.

Repinned it and now just the dataset faults remain. Hopefully the swapping if module corrects this.

You make a Lot by the car , buy a vnci Red

If the other module doesn’t work then it may well be cheaper to buy one and get you to connect than get a garage to code it! I will consider it. Although I’m not sure there’s any other retrofits I will do that will need it.

We have some success! New module works without any dataset changes required. No DTC on park assist module.

However I do have 2 DTC on module 17.

I did enable byte 5 bit 4 as per some instructions I found online, but carscanner doesn’t have the same long coding helper that vcds does so I may have done it wrong. @Cairus can you tell from the following what I’ve done wrong?

Car Scanner ELM OBD2

Version: 2.1.46/2.1.46/iOS

DTC report

Connection profile: Skoda MQB, PQ26: Diesel DPF var.1 [EA288]Date: 9/4/2026 1:45:16 PM

VIN: TMBKJ7NP9G70XXXXX

============================

OBD-II

No DTC found.

============================

17. Dashboard17. Dashboard

DTCs: 2

----------------------------

13636608 [0xD01400]

U101400: Control module incorrectly coded

Steuergerät falsch codiert

U101400: Control module incorrectly coded

ECU incorrectly coded

Status bits: 1

Priority: 2

Frequency: 1

Unlearning index: 91

Odometer: 213909 km

Date, time: 2026.09.04 13:44:33

Status: Test failed, Confirmed

----------------------------

16776980 [0xFFFF14]

U112100: Databus missing message

PLA_Status keine Kommunikation

U112100: Databus missing message

PLA_Status_01 communication error can_error_timeout

U112100: Databus missing message

PLA_Status_01 keine Kommunikation

Status bits: 1

Priority: 6

Frequency: 1

Unlearning index: 91

Odometer: 213909 km

Date, time: 2026.09.04 13:44:33

Status: Test failed, Confirmed

10. Parking Assistant 2

Application data identification: bL

VAG Part number: 5QA919294B

Software version: 0044

ECU manufacturing date (ASCII): 170813

ECU serial number: 00030841861722200441

Hardware Part number: 5QA919294

System supplier ECU hardware number: 00030841861722200441

System designation: PDC 8 Kanal

Calibration date (ASCII): (

ASAM/ODX: EV_EPHVA18AU3700000

Hardware version: H07

ASAM/ODX version: 009035

FAZIT Identification: ATW-00113.08.17EC060080

Parameter set part number: V03935264LH

Parameter set version: 0001

System abbreviation: J446

ECU manufacturing date (HEX): 170813

Date of last adaptation: 170828

Date of last coding: 000000

Diagnostic mode: 03

Parametrization date: 170825

Long Coding: 0471051811

--------------------

17. Dashboard

Application data identification: --------------------------

VAG Part number: 3V0920941

Software version: 6422

ECU manufacturing date (ASCII): 151119

VIN: TMBKJ7NP9G7041006

Hardware Part number: 3V0920941

System supplier ECU hardware number: A2C945862040000_D2255

System supplier ECU software number: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

System designation: KOMBI

Calibration date (ASCII): &)

ASAM/ODX: EV_DashBoardVDDMQBAB

Hardware version: 213

ASAM/ODX version: 009046

FAZIT Identification: VD1-04819.11.1573958407

Parameter set part number: -----------

Parameter set version: ----

System abbreviation: J285

ECU manufacturing date (HEX): 151119

Date of last adaptation: 260329

Date of last coding: 260902

Diagnostic mode: 03

Parametrization date: 000101

Long Coding: 27A5090A2F90A60001887A011000000000000000

1 hour ago, Binx1310 said:

Wir haben einen Erfolg erzielt! Das neue Modul funktioniert ohne jegliche Änderungen am Datensatz. Kein Fehlercode (DTC) am Einparkhilfemodul.

Allerdings habe ich 2 Fehlercodes (DTCs) auf Modul 17.

Ich habe Byte 5 Bit 4 gemäß einer Anleitung, die ich online gefunden habe, aktiviert, aber CarScanner verfügt nicht über die gleiche lange Codierungshilfe wie VCDS, daher habe ich es möglicherweise falsch gemacht. @Cairus Können Sie anhand des Folgenden erkennen, was ich falsch gemacht habe?

Fahrzeugscanner ELM OBD2

Version: 2.1.46/2.1.46/iOS

DTC-Bericht

Verbindungsprofil: Skoda MQB, PQ26: D codiert

Statusbits

Byte 5 Bit 04 is wrong. Turn off

Byte 13 Bit 0-3 Set to yes ---> High

12 minutes ago, Cairus said:

Byte 5 Bit 04 is wrong. Turn off

Byte 13 Bit 0-3 Set to yes ---> High

I have rolled back the byte 5 bit 4 change.

Which bits do I enable on byte 13?

This is what I see on carscanner.

Byte 13 ---> HEX 01

7 minutes ago, Cairus said:

Byte 13 ---> HEX 01

perfection. Thanks once again for your never ending assistance!

You are Welcome

Whats the button highlighted in yellow? I guess the one next to it is to turn the sound on and off.