On 03/02/2024 at 08:38, Esseesse200 said:

272 estate with koni specials an H&R springs. 12mm spacers all round with 19’s and 15mm spacers with 18” winters  No rubbing not even loaded fully.

 

Hi appreciate it’s been some time since this thread but could you possibly post some pics of your car with the 12mm spacers from maybe down the side of the car to show how much the Vega’s fill the arches width ways? Love the look of yours with the lowering kit. 👌🏼
I have a hatch and was looking at 13mm front and 16mm rear but not sure if that’s too much. 
Car will remain on standard suspension for now. 👍🏼 Thank you. 

Bit frustrating, when I called up EibachUk about having the Q2 springs F11-85-043-02-fa for the front and the iV springs F11-85-016-10-HA for the back they got a bit funny and said I could order them but they’d be a special order and I couldn’t return them or have a warranty 😕

@globalste Just phone up and say you are fitting them to a Q2.  I'm sure You can get a pair (or single) springs from ebay.  I was going to do that but found a good enough set targeted at a 4motion passat.

2 hours ago, globalste said:

the Q2 springs F11-85-043-02-fa for the front and the iV springs F11-85-016-10-HA

still without manufacturer warranty, here is a positive experience with the Eibach Pro Kit from the Kodiaq

 

2023. Mk3.FL 2.0 TSI 280ps AWD

challenge, stiffness without lowering, succeed

 

front

Eibach F11-85-043-03-FA + Bilstein B6 DampTronic 23-254343

rear

Eibach F11-79-013-01-RA + WRONG Bilstein B6 DampTronic 20-254353 (correct part code would be 20-267537)

 

 

more info -> https://www.briskoda.net/forums/topic/510961-2023-280ps-lk-replaced-2016-220ps-style/?do=findComment&comment=5854160

 

 

 

Hi All,

Just wanted to get everyone's confirmation that E10-79-012-04-22 is the correct kit for a 2020 Estate with DCC ? Just looking for that 25mm approx. drop.

 

Edited 1 December, 20241 yr by defsix

5 hours ago, defsix said:

Hi All,

Just wanted to get everyone's confirmation that E10-79-012-04-22 is the correct kit for a 2020 Estate with DCC ? Just looking for that 25mm approx. drop.

 

Correct 👍 

 

These r the relevant Eibach Pro-kit springs part numbers.

Kit ordered, hopefully on the way soon.

 

Hopefully VCDS will be successful doing a DCC Adaption!

 

VCDS MQB DCC Adaption Method

The DCC Recalibration is highly recommended after lowering, or raising the car springs.

 

I did mine via OBDEleven.

So for Sportline 2017 2.0TDI 140kw FWD I will go with F11-85-041-01-VA ? Got DCC I believe as I can select Comfort drive mode.

I read all over the forums that the front is a bit more lowered with that kit. So is there alternative to have it even?

5 hours ago, Critt92 said:

So for Sportline 2017 2.0TDI 140kw FWD I will go with F11-85-041-01-VA ? Got DCC I believe as I can select Comfort drive mode.

I read all over the forums that the front is a bit more lowered with that kit. So is there alternative to have it even?

That part number is just the front springs alone.

The full set is the one before it, beginning with E10.

Hence if u have a FWD 2.0TDi Sedan u need E10-85-042-02-22.

If u have the FWD 2.0TDi Wagon version u need E10-79-012-03-22.

I have the sedan version, both front and rear sit at the same height.

Edited 16 March16 Mar by JR RS