-
Yeti 5L: byte 18 changed, need BCM light config (VCP) - halogen
As far as I know, if byte 18 was 00 then no byte 18 value is correct for that vehicle. Some might be close enough that everything seems to work but there will be a difference that an engineer in VAG thought was important. Byte 18 mostly deals with lighting channels that aren't the headlights or front fog lights. As long as the example you find from VAGhelper has the same rear lights (halogen or LED) then I think you have a very good chance.
-
Rear diffuser fins
Looks like it's HSK 3D who makes them in the UK. https://hsk3d.co.uk/store/skoda-octavia-mk3-rs-vrs-rear-diffuser-fins-3d-printed-bumper-splitter-styling https://www.ebay.co.uk/itm/318144171141
-
langers2k started following Skoda Octavia 2019 reverse camera , Rear diffuser fins , Yeti 5L: byte 18 changed, need BCM light config (VCP) - halogen and 4 others
- Yeti 5L: byte 18 changed, need BCM light config (VCP) - halogen
-
Can I enable Indirect (ABS wheel sensor based) TPMS on 2012 Yeti SE?
For the non-maxidot version, I'm pretty sure it's: 03 - byte 16, bit 2 17 - byte 2, bit 0 There will be no 4C module and the reset can either be done with VCDS or a physical switch.
-
Can I enable Indirect (ABS wheel sensor based) TPMS on 2012 Yeti SE?
That ABS module is definitely capable of indirect TPMS - being a Yeti has nothing to do with it VCDS is asking the gateway which is correctly stating there is an unregistered module. Neither VCDS or the gateway know if it's a real module or a virtual one, regardless you need to add 4C to the gateway installation list and then it's fixed. For example, "46-Central Conv" is shown in your installation list currently - however, that's also a virtual module (created by 09). It's not unusual in the VAG world. I don't think there is much documentation about the learning procedure. I would guess at least 10-15 minutes of 15mph+ driving should get a OK baseline and hopefully a complete calibration after an hour or so. Just as an example from another forum regarding indirect TPMS on a MK60EC1: Drove about 50 miles with equally inflated, sensorless tires. No TPMS light or other warnings on dash Deflated one of the rear tires slightly, by about 8% (38 -> 35). Drove about 5 miles. No warning light. Deflated same tire by about 20% of original value (38 -> 31). TPMS warning light appeared after about a mile. edit: Slightly older MK60EC1 in another Yeti showing it working without the phycial button. They had to use VCDS to reset the learning each time instead: https://www.briskoda.net/forums/topic/192503-yeti-with-tpms-switch-abs-module-coding-required/ The extra coding changes and adding 4C is only required to enable reset via maxidot cluster. They also suggest an hour calibration drive.
-
Can I enable Indirect (ABS wheel sensor based) TPMS on 2012 Yeti SE?
4C is a virtual module, it's not expected to be diagnostic compatible. I don't have my MK2 Octavia any more but that was SW:0608 for the cluster and did support reset via maxidot. It was also the same ABS module. Just to confirm, you changed the ABS coding from 933F400E09260102C91302EA9022808A300000 to 933F400E09260102C91302EA9022808A360400 ? IIRC, byte 16 bit 1 doesn't have a checkbox so you need to modify it manually. Then do the instrument cluster and gateway installation list changes.
-
Can I enable Indirect (ABS wheel sensor based) TPMS on 2012 Yeti SE?
I doubt driving around a block is long enough for the system to relearn. On a MY12, you probably don't even need a button assuming you have a maxidot cluster running SW: 06xx or newer... Try these instructions: https://www.briskoda.net/forums/topic/363554-tpm/#findComment-4746144
- What wheels are these on a Mk3 Superb 2016
-
Amundsen MIB2 update
You're looking at the wrong instructions at a guess. The Columbus has MIB1/MIB2 folders, the Amundsen doesn't. Just follow these instructions: https://www.briskoda.net/forums/topic/491705-how-to-update-maps-on-mib2-or-mib25-amundsen/
- Wheel Bolts for Alloys v Steels
- Wheel Bolts for Alloys v Steels
-
a small project
I wonder if there will ever be a ethernet <-> optical solution for virtual clusters.
-
Skoda Octavia 2019 reverse camera
Perhaps you should read the post I linked more carefully... Quick google later: https://www.aliexpress.com/item/1005006269260355.html You want "OCTAVIA MK3" or "OCTAVIA MK3 WASH" not "OCTAVIA MK3 LOWLINE".
-
Skoda Octavia 2019 reverse camera
If you look at the second post in the thread mentioned above, it's a post from me fitting a genuine highline camera: https://www.briskoda.net/forums/topic/485897-how-to-reverse-camera-fitting-guide/#findComment-5456364 Highline cameras will work without calibration, but if you do want it calibrated, I also added details a few posts later: https://www.briskoda.net/forums/topic/485897-how-to-reverse-camera-fitting-guide/#findComment-5461654
-
a small project
Can you add more details?
langers2k
Resident Member
-
Joined
-
Last visited