How To: Heated Windscreen Retrofit

[ApertureS]

How to: Heated Windscreen Retrofit 

  

All of this is done at your own risk and is just meant as a general guide, not a full instruction manual. Just cause some things may work for my car may not mean the same for yours. 

  

Parts List 

  

3V0845011AE - Heated Windscreen WITH A5 camera support - Will be different for everyone so confirm it first! 

3V0907044DA - Dash Control Panel with heated windscreen button - Will be different for everyone so confirm it first! 

071973851 x2 - Large Plug Housing for Heated screen connector 

000979307E - Pins for large plug, comes with 2 pins so only order 1 

000979425E - Pins for relay with 6mm wire attached, comes with 2 pins 

000979027E - Pins for relay with 0.5mm wire attached. comes with 2 pins 

4H0951253A - 645 Relay for main current flow  

5Q0937507D - Relay holding plate, my car already came with but heres the part number 

000979424E - Pins for Jtype fuse in engine bay fuse box with 6mm wire attached, comes with 2 pins 

N91186305 - 50A Slow blow fuse for heated screen 

6mm repair wire - Only required 2 meters to be on the safe side (red) 

0.5mm repair wire - Yellow/red repair wire 5m 

0.5mm repair wire - Red/yellow repair wire 5m 

Fuse box terminal - Was not required as it splices into already used OEM pin for climate control 

000979009E - Small pin for BCM plug with wire attached 

Varied Conduit - For wrapping the under bonnet looms to give an OEM feel and protect them 

Loom tape - for wrapping wiring and securing inside and outside cabin 

Heat shrink crimp connectors - These are genuine repair methods so order both 1mm and 6mm versions 

Silicone - For sealing the exterior connectors 

  

You will need VCDS & ODIS for this or equivalents.  

  

Once you have your parts together and your screen is fitted you will have 3 additional connections, 1 in the headliner, 2 at the base of the windscreen. 

  

 

 

 

 

Wiring Diagram

For anyone that fancies going alone and doing the wiring themselves, here is the only wiring diagram you need.

 

 

Fitting ground wire 

  

To start you'll need to drop the front interior lamp, this is done by opening the sunglasses holder and pulling the trim off around the SOS button and around the interior light buttons. Pull the interior light unit out of the housing and if need be remove the torx screws to drop the entire assembly out of the way. Here you will see the 10mm ground stud with a nut on it, remove the nut and fit your ground strap before tightening back up - DONT go crazy as it will tear the strap. 

 

  

 

Run wires through bulkhead 

  

You'll now need to run your 2x 0.5mm wires through the bulkhead, this can be fiddly so a coat hanger of some kind makes the job a lot easier, to start, remove the battery and battery tray to expose the main wiring loom which will be under a plastic cover and disapear into the passenger rear most corner of the bulkhead, the best way to do this is to poke a small hole from the outside in with the coat hanger, then from inside the car, go up under the glovebox and behind the blower motor, you will just see the end of the hanger, attach a wire to it and pull it back through. It might take a few tries to get right and just make sure you don't tear the boot or damage other wires.  

These 2 wires will be going from the interior fuse box area to the under bonnet fuse box so run them either inside the original loom or use some small conduit to keep them protected under the bonnet from road grime and heat.  

Whilst you are here, get your 6mm red wire and run it from the under bonnet fuse box area, through the plastic casing under the battery, then up the loom which heads into the scuttle panel area. Again, protect this wire with conduit or run it inside the original loom.  

 

  

 

Wire up windscreen power supply 

  

Now you have the large 6mm wire in the scuttle area, you need to remove the wiper arms which is done with 2x 13mm nuts under plastic covers, once the nuts are off, gently press on the pivot point of the wiper arm to release the entire arm making sure not to damage the screen. There are 4/5 metal clips holding the plastic scuttle covers down, these just pull off. Then starting at the outer most edge of the screen where it meets the plastic, slowly lift to remove all the plastic covers. Do this on both sides to fully expose the lower screen/scuttle area. You should now see your 2 large connectors with brown wires running into the windscreen. You will need to run your 6mm wire to both of these. You may choose a different method but mine was; place the 4mm wire with male pins inside the connector and push the purple tab inside the connector across till it clicks, I then placed the connectors in a vice and filled the rear with silicone to prevent any water getting in. The yellow wire was then cut in half. I ran the red wire all the way to the drivers side of the screen and used a OEM crimp connector to attach the 4mm wire to the 6mm wire. 

For the passenger side, I cut some of the insulation off the red 6mm wire near the passenger side and soldered the wires together. You will need a big soldering iron for this as the wires are massive.  

Both connections should be water tight. Secure the new wiring to the original loom and play close attention to making sure the drivers side connector will not make contact with the wiper motor as this will rip the wiring apart. 

Also make sure the connectors are not sitting in the lower section of the scuttle panel as this gets full of water, the flat part of the connectors should not be kinked either as it will damage the flat wires. 

Refit all the plastic trim and wiper arms - Use the dirty marks on the windscreen to line the arms back up, short wiper always goes on the passenger side. 

  

 

  

Wire up interior fuse box 

  

Next we are back inside the car and need to remove the glovebox to access the rear of the fuse box. This is done with around 8 torx screws both under and inside the glovebox, slowly lower the glovebox and make sure to disconnect all plugs. I also disconnect all plugs for the infotainment system and move the glovebox completely out of the way to give yourself more space. Now you should see your 2 wires that came through the bulkhead, we only want the red with yellow trace wire right now. Run it neatly towards the fuse box, pull the fuse box forward using the small plastic tabs giving enough room to access the back of it. At this point remove fuse 7 which is a 10A one. Find the red/yellow wire behind the fuse box that goes into fuse slot 7 it will be on the top row, this is where we want to splice our own red/yellow wire to. Make sure to use heat shrink and solder or OEM crimp connector.  

 

Place the fuse box back but DO NOT refit the fuse yet. 

  

 

 

  

Wire up body control module 

  

This will be our last wire under the glovebox area which is our yellow with red trace wire. You will be able to see the body control module (bcm) on the left hand side of the fuse box, it will look awkward to get to but the trick is, it doesn’t need to be fully removed. 

Where the lower foot well trim meets the side trim you will want to pull up on the side trim, this means you can tell pull the footwell trim out of its clip and remove it fully, once this is out the way you will see a big group of connectors we don't need any of these but instead, you should be able to see the BCM plugs directly above this group of connectors, 3 big plugs, we want the centre one, once the white locking lever is pulled down, you can pull the connector out of the unit then down a track and it will come out under the BCM area, cut the cable tie on the plug if there is one, press the 2 locking tabs in and release the inside of the plug. You will now want to run the yellow/red wire neatly to the plug you have just stripped down, attach the very small pins wire to the end of the yellow/red wire using solder or an OEM crimp connector. The plug you now have will be numbered for each pin hole, you are looking for pin location 26. Insert your pin into this until you hear a click, put the plug back together, secure your new wire to the loom and refit the plug in the opposite way to what you took apart. 

 

Refit all the trim at this point, including the glovebox unit but NOT THE FUSE - if you put the fuse back in with exposed wires under the bonnet you will blow it. 

  

 

Wire Up Under Bonnet Fuse Box 

  

You will now have your 3 wires at the under bonnet fuse box, you want to cut the cable tie where the wires run into the fuse box and then remove the inside section of the fuse box, this is fiddly as the little clips around the outside are a very tight fit.  

Once you are in and you can access the underside of the fuse box.  

In your parts pile you will need to find your 2 sets of repair terminals, all 4 ends will have the same terminal but 2 will be thick wires, 2 will be thin. Cut these in half so you have 4 individual wires with terminals. 

Attach the thin wire ones to the red/yellow and yellow/red wire. These need to be inserted into the correct relay points. Refer to the photo below which is the brown wire and yellow/red 

wire you see in the photo, they can go in either slot. This leaves us with 1 more red wire which runs to the windscreen, crimp one of your last 2 big terminal repair wires to it and insert into the LOWEST yellow wire point you see on the relay. 

 

Youre nearly there now!  

 

You now need to take your 2 large flat male pins with 6mm wire and you will need to cut this in half, this will leave you with 2 large male connectors and 1 large female connector all with 6mm wires. Join one of the large male and female wires together with a wire length of about 10cm. The female end will need inserting into the top relay connector which is pictured with a yellow wire. The male end will go to the fuse holder, this is shown in my picture with a red wire with grey trace and it shows where it must go, take note it will only go in one way round. 

The final wire which is 1 last big male terminal will need inserting next to the one you just inserted, this will give you your 2 pins for the fuse.  

The other end of this wire I placed securely under one of the large nuts with a red wire already attached to it. This is to supply the 12v constant supply required. This is shown pictured as a purple and black wire. Make sure all wire strands are secured and none are left to short out anywhere. 

  

At this point you can now insert your 645 relay and your 50A fuse. Put all the fuse box back together making sure no wires get caught anywhere, refit all trim, battery and everything else you took apart. You can NOW fit the 10A fuse back inside the car by just dropping the glovebox down, release the hinge on the side and with the 2 clips inside it it will lower to access the fuse board fully. 

  

  

 

 

 

 

 

 

That is all the wiring done! Only 2 more things to do now.  

  

  

  

Change display unit 

  

At this point you should have your new climatronics panel with the heated windscreen button. If you couldn't work out which one you needed, drop me a message. The key is 4GW = Heated front screen. 

 

First you will want to connect your VCDS to the car and SAVE YOUR CURRENT LONG CODING for module 08. If you don't do this, you'll run into trouble. 

 

Now remove the old unit, pull the plastic trim from underneath to remove it, then do the same with the actual unit no screws, just clips, remove the 3 connectors on the back and fit your new unit in the reverse order. 

You will notice that you cant turn the fan on or do anything with the heating yet. Don’t panic. 

 

  

  

Coding 

  

Once this is all done you can relax and just do the coding side of things now. 

Connect ODIS/VCDS to the vehicle and run the basic settings on the unit, this will teach the new unit your heater flap positions.  

Now put your old long coding back into the unit to save time and make sure everything is how it should be. You now want to open the long coding to make your modifications as follows: 

 

Byte 5 bit 0-3: 04 Windshield Glass A/C Comfort Glass [PR-4GW] 

Byte 11 bit 0: Windshield Defogger/Heater installed [PR-4GW] 

  

At this point, clear codes, turn the car off and lock it up for 15 minutes to allow the car to reset the canbus network. Get in, start the car and just confirm the heater is all working again as it should be. The windshield heater will not turn on but the button will flash at this point when pressed. 

  

Go to module 09 which is your BCM, Enable security access and go to your adaptations, you are looking for IDE04927-ENG142021-Window heater-Heizbare_Frontscheibe this needs to be changed from Not installed to installed. 

  

  

  

  

  

And that is it. You are all done, heated windscreen fully working. 

 

Some of you may notice the empty ADAS A5 camera spot, hopefully another guide for that will be coming in the near future as i fit it all up.

  

Any issues with the guide or comments, let me know. 

  

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Edited 15 August, 2021 by ApertureS

[mbucge]

thank you so much

[ColinD]

Fantastic effort on this guide!

[MikeM46]

Epic how-to post!!!

[Matt0020190]

Excellent tutorial well done

 

Thanks to your guide I managed to fit the screen to my VW Touran. Being part of the VAG group the installation is very similar.

 

The only differences for VW to your instructions are as follows:

 

1. Climatronic control panel does not need to be replaced. VW don't have a dedicated physical button sadly and only the infotainment screen can turn it on/off. Simply coding as per your instructions works fine.

 

2.

The wiring diagram for VW is simpler. No fuse in the interior car fuse box. There are 3 fuses to be installed in the engine fuse box only with two relays. The BCM wire at T46 still remains the same.

 

Coding and everything else remains identical. So thanks for helping a VW user out here too!

 

PS- I've also retrofitted the ADAS camera. It's the same for Skoda so if you need any help let me know.

 

All the best

[ApertureS]

On 10/02/2022 at 20:38, Matt0020190 said:

Excellent tutorial well done

 

Thanks to your guide I managed to fit the screen to my VW Touran. Being part of the VAG group the installation is very similar.

 

The only differences for VW to your instructions are as follows:

 

1. Climatronic control panel does not need to be replaced. VW don't have a dedicated physical button sadly and only the infotainment screen can turn it on/off. Simply coding as per your instructions works fine.

 

2.

The wiring diagram for VW is simpler. No fuse in the interior car fuse box. There are 3 fuses to be installed in the engine fuse box only with two relays. The BCM wire at T46 still remains the same.

 

Coding and everything else remains identical. So thanks for helping a VW user out here too!

 

PS- I've also retrofitted the ADAS camera. It's the same for Skoda so if you need any help let me know.

 

All the best

Youre very welcome, glad it came in handy. 

 

Ther superb is i believe the only model to have a single relay and a back and forward trigger for it.... everything else including the octavia uses 2 relays under the bonnet and a single wire from inside the car, not 2. That being said, for simplicity you could very easily just take a feed from the front fuse box instead of the interior fuse box. 

 

ADAS was retrofitted quite a while ago in mine but thanks for the offer. 

[Matt0020190]

4 minutes ago, ApertureS said:

Youre very welcome, glad it came in handy. 

 

Ther superb is i believe the only model to have a single relay and a back and forward trigger for it.... everything else including the octavia uses 2 relays under the bonnet and a single wire from inside the car, not 2. That being said, for simplicity you could very easily just take a feed from the front fuse box instead of the interior fuse box. 

 

ADAS was retrofitted quite a while ago in mine but thanks for the offer. 

Great stuff!

 

How do you find the heated screen? Worth the money? Probably cost me about £175 to fit including windscreen excess. I've yet to test it as I've had no frosty mornings!

 

Does it clear quickly?

 

I've also changed the adaptation in the module for "Windscreen heating on MAX defrost". In theory when you press the MAX defrost button the windscreen heater is supposed to come on too. Have you seen similar?

 

The only indication I have at the moment my work is working is there is a slight rev drop when pressing the button. I don't hear any relay click but I guess the engine drowns that out.

 

Let me know if you don't mind. Thanks again

[ApertureS]

16 minutes ago, Matt0020190 said:

Great stuff!

 

How do you find the heated screen? Worth the money? Probably cost me about £175 to fit including windscreen excess. I've yet to test it as I've had no frosty mornings!

 

Does it clear quickly?

 

I've also changed the adaptation in the module for "Windscreen heating on MAX defrost". In theory when you press the MAX defrost button the windscreen heater is supposed to come on too. Have you seen similar?

 

The only indication I have at the moment my work is working is there is a slight rev drop when pressing the button. I don't hear any relay click but I guess the engine drowns that out.

 

Let me know if you don't mind. Thanks again

A fully frosted and solid with ice windscreen will be wipable with the wiper blades in about 3-5 minutes roughly. Also stops any condensation build up on the inside. I get in the car, switch the heated screen, seats and mirrors on and by the time ive set the nav and picked a song its almost ready to go. Would love the heated steering wheel next though. 

[ColinD]

I use the heated steering wheel far more than I should. Poor circulation.

 

I don’t mind scraping the windscreen, it is heated but I forget more than I remember.

 

the heated wheel though, just perfect  for cold or slight wet days

 

so get it done  not that I know how. 

[Matt0020190]

11 minutes ago, ApertureS said:

A fully frosted and solid with ice windscreen will be wipable with the wiper blades in about 3-5 minutes roughly. Also stops any condensation build up on the inside. I get in the car, switch the heated screen, seats and mirrors on and by the time ive set the nav and picked a song its almost ready to go. Would love the heated steering wheel next though. 

Cheers for that sounds good

 

I've done the steering wheel also. Wasn't too hard at all. Main challenge was changing my clockspring to support the heated wheel. Other than that the rest was straightforward.

 

That's cool too as all I do is tap the heated seat button and the wheel comes on too. Even better if the outside temperature is less than 3 degrees, it turns on automatically also

[J.R.]

57 minutes ago, Matt0020190 said:

Probably cost me about £175 to fit including windscreen excess.

 

So you scammed your insurers?

[Matt0020190]

2 hours ago, J.R. said:

 

So you scammed your insurers?

No scam when your windscreen is  genuinely cracked. All legit thank you and checked with them directly prior. Appreciate your constructive contribution to the topic.

[J.R.]

Do you mean that the excess which you paid was for the difference in price between the replacement cost of your cracked non heated screen and a heated one?

[Matt0020190]

Yes, the difference was my excess price between the two

[SuperSK]

Thank you for your excellect guide! I am potentially looking at getting this done once I find a windshield I can take off a breakers yard. Maybe for my wifes Golf too as it tends to have alot of condensation!

 

Both you and Matt0020190 mentioned coding for other units, but nothing for the radio? Does the heated windshield button appear in the air conditioning settings once you retrofit it with no extra coding?

 

Thank you again!

[ApertureS]

57 minutes ago, SuperSK said:

Thank you for your excellect guide! I am potentially looking at getting this done once I find a windshield I can take off a breakers yard. Maybe for my wifes Golf too as it tends to have alot of condensation!

 

Both you and Matt0020190 mentioned coding for other units, but nothing for the radio? Does the heated windshield button appear in the air conditioning settings once you retrofit it with no extra coding?

 

Thank you again!

Exactly yes, the only 2 modules effected are the HVAC and Central Electronics. The 5F radio will display the button automatically.

[Agustnr]

Sorry for bumping this and asking a stupid question, but should you ideally do the wiring prior to the windscreen fitting or it doesn't matter?

[ApertureS]

6 hours ago, Agustnr said:

Sorry for bumping this and asking a stupid question, but should you ideally do the wiring prior to the windscreen fitting or it doesn't matter?

Either way round is fine. Just isolate any open connectors from the elements 

[M17HSN]

Hi ApertureS would you know the items needed for a passat b8 and the costs involved?

[ApertureS]

1 hour ago, M17HSN said:

Hi ApertureS would you know the items needed for a passat b8 and the costs involved?

They won’t be too far different, if you wanted to let me know your registration I can work it out.

 

When you say costs, did you mean you want the price for it fitted? 

[M17HSN]

hi ApertureS

 

I'm not that familiar with mechanics\electrics etc so it's either sourcing someone in Lancashire to fit everything or finding someone who can fit it.  I would be grateful if you can fit it then give me a price, if not then if you can give me a price for the components.  The reg number MD68TYV

[ApertureS]

1 hour ago, M17HSN said:

hi ApertureS

 

I'm not that familiar with mechanics\electrics etc so it's either sourcing someone in Lancashire to fit everything or finding someone who can fit it.  I would be grateful if you can fit it then give me a price, if not then if you can give me a price for the components.  The reg number MD68TYV

For your car:

 

3G0845011ACNVB - heated glass, without lane assist camera - retails roughly £1000

 

3G0845011BBNVB - heated glass with lane assist camera prep - retails roughly £900

 

 (Weird how the lane prep glass is cheaper)

This is the prices for genuine glass, of course aftermarket glass is also a cheaper option and you have the choice of with/without lane assist prep which can also be retrofitted at the same time if not already fitted.

 

If you wanted to discuss it being fitted any further please drop me a message on my signature below or private message me  if you wanted to consider doing it yourself please continue to ask questions here as it can assist others too 

 

thanks  

[JonnyC90]

Hey! Anyone else had issues with changing the climate control panel?

 

My initial version was a 3V0907044DA (manufactured 2018) and managed to get my hands on an older 3V0907044AJ from a 2015. The panels look a little different but otherwise seem to be a good match (the new one is a matt black instead of the piano gloss but after another week of wiping fingerprints from it I was happy for the change!).

 

Anyway managed to get it installed and coded with VCDS with the original coding but now it won't show up on the infotainment screen - just shows off and won't pop up when pressing the "settings" button.

 

Anyone else had this issue? Any ideas on a fix?

[ApertureS]

7 hours ago, JonnyC90 said:

Hey! Anyone else had issues with changing the climate control panel?

 

My initial version was a 3V0907044DA (manufactured 2018) and managed to get my hands on an older 3V0907044AJ from a 2015. The panels look a little different but otherwise seem to be a good match (the new one is a matt black instead of the piano gloss but after another week of wiping fingerprints from it I was happy for the change!).

 

Anyway managed to get it installed and coded with VCDS with the original coding but now it won't show up on the infotainment screen - just shows off and won't pop up when pressing the "settings" button.

 

Anyone else had this issue? Any ideas on a fix?

Any fault codes?

Can you connect to it via diagnostic?

 

I think your issue is you’ve fitted a much older control unit and it’s not compatible, but would need to see the fault codes first to know.

 

The one you have fitted won’t have functionality for a bypass valve compressor and only a magnetic clutch so coding it to have one would do nothing. (Unless it’s got newer software on it)

[JonnyC90]

2 hours ago, ApertureS said:

Any fault codes?

Can you connect to it via diagnostic?

 

I think your issue is you’ve fitted a much older control unit and it’s not compatible, but would need to see the fault codes first to know.

 

The one you have fitted won’t have functionality for a bypass valve compressor and only a magnetic clutch so coding it to have one would do nothing. (Unless it’s got newer software on it)

 

Cheers for the help @ApertureS

 

I did wonder if it might be a bit old.

 

I do have some codes show up in VCDS mainly relating to the rear vents that don't show up with the original unit:

 

Chassis Type: NP-SK48 (3Q0)
Scan: 01 02 03 05 08 09 10 13 15 16 17 19 2B 36 42 44 4B 52 5F 6C
          75 BB BC

VIN: TMBBJ7NP1J7570828   Mileage: 102997km-63999miles

01-Engine -- Status: Malfunction 0010
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
13-Auto Dist. Reg -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
2B-Steer. Col. Lock -- Status: OK 0000
36-Seat Mem. Drvr -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
4B-Multifunc. Module -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
5F-Information Electr. -- Status: OK 0000
6C-Back-up Cam. -- Status: Malfunction 0010
75-Telematics -- Status: OK 0000
BB-Door Rear Drv -- Status: OK 0000
BC-Door Rear Pass -- Status: OK 0000
-------------------------------------------------------------------------------
Address 01: Engine (J623-DFHA)       Labels:. 04L-907-309-V1.clb
   Part No SW: 04L 906 026 TM    HW: 04L 907 309 P
   Component: R4 2.0l TDI   X25 6312  
   Revision: B4X25---    CVN: 6369B71DB866C2AD00000000
   Coding: 01250412036405083000
   Shop #: WSC 00000 000 00000
   ASAM Dataset: EV_ECM20TDI01104L906026TM 005001
   ROD: EV_ECM20TDI01104L906026TM_SK48.rod
   VCID: 0849976C22B4A17A673-805C
   VINID: 91D4926877A005A1C51C020220FCC39D2A

1 Fault Found:
28992 - No Communications with NOX Sensor 2 
          U029E 00 [00100111] - -
          Not Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Priority: 2
                    Fault Frequency: 1
                    Mileage: 102997 km
                    Date: 2024.04.29
                    Time: 08:28:35

                    Engine RPM: 0.00 /min
                    Normed load value: 0.0 %
                    Vehicle speed: 0 km/h
                    Coolant temperature: 85  C
                    Intake air temperature: 78  C
                    Ambient air pressure: 990 mbar
                    Voltage terminal 30: 12.220 V
                    Unlearning counter according OBD: 40
                    Limitation: accelerator pedal: 0.0 Nm
                    CAN status - engine control module-Bits 0-7: 0
                    Cruise Control System (CCS): status-Bits 0-7: 0
                    CAN status - transmission control module-Bits 0-7: 0
                    CAN status - brake control module 1-Bits 0-7: 0
                    CAN status - brake control module 2-Bits 0-7: 0
                    selected gear-Bits 0-7: 0

Readiness: 0 0 0 0 1 

-------------------------------------------------------------------------------
Address 02: Auto Trans (J743)       Labels:. 0BH-927-711.clb
   Part No SW: 0GC 300 042 H    HW: 0GC 927 711 G
   Component: GSG DQ381     H06 1403  
   Revision: 00H06V07    CVN: FC60F4E0
   Coding: 0014
   Shop #: WSC 00000 000 00000
   ASAM Dataset: EV_TCMDQ381061 001
   ROD: EV_TCMDQ381061.rod
   VCID: 2B0308E0D382AA62AA1-807E

   No subsystems: 

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104)       Labels: 5Q0-907-379-IPB-V1.clb
   Part No SW: 5Q0 614 517 DA    HW: 5Q0 614 517 AH
   Component: ESC           H62 0753  
   Revision: 00000000    Serial number: 60338000000687
   Coding: 1D07929C34270B6C477F060240CB49B8492CD0E2600292753861F078C209420B00000012121212B835351919323200
   Shop #: WSC 00046 000 00000
   ASAM Dataset: EV_Brake1UDSContiMK100IPB 037009
   ROD: EV_Brake1UDSContiMK100IPB_037_VW37.rod
   VCID: 73B3D0804B32B2A2221-8026

No fault code found.

-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. (J518)       Labels:| 5Q0-959-435.clb
   Part No SW: 3Q0 959 435 G    HW: 3Q0 959 435 G
   Component: VWKESSYMQB    037 0907  
   Revision: 00037000    Serial number: 0468930754 Dataset Number: V03935254SK 0001
   Coding: 032C0C070F
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_KessyHellaMQBAB 004041
   ROD: EV_KessyHellaMQBAB.rod
   VCID: 3E2531B430F02FCA1DF-806A

   Rear lid opener control module: 

No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC (E87)       Labels:| 3V0-907-044.clb
   Part No SW: 3V0 907 044 AJ    HW: 3V0 907 044 AJ
   Component: AC Automat    H32 3601  
   Revision: 20K04000    Serial number: 00000B00034578
   Coding: 11110104002110011005004C0010102A
   Shop #: WSC 33361 790 00063
   ASAM Dataset: EV_ACClimaPrehVW37X 002009
   ROD: EV_ACClimaPrehVW37X_002_VW37.rod
   VCID: 7CA1FBBC666CFDDA73B-8028

2 Faults Found:
197634 - Temperature Sensor for Rear Vent 
          B1089 15 [00001001] - Open or Short to Plus
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Priority: 3
                    Fault Frequency: 1
                    Reset counter: 58
                    Mileage: 102997 km
                    Date: 2024.04.29
                    Time: 08:28:33

                    Outside temperature: 15.5  C
                    Vehicle speed: 0 km/h
                    Voltage terminal 30: 12.1 V

328455 - Position Sensor for Rear Temperature Flap Motor 
          B1096 15 [00001001] - Open or Short to Plus
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 58
                    Mileage: 102997 km
                    Date: 2024.04.29
                    Time: 08:28:33

                    Voltage terminal 30: 12.1 V
                    Inside temperature: 12.5  C
                    Outside temperature: 15.5  C
                    Rear temperature flap: actual value: 0.0 %
                    Rear temperature flap: actual value: 512
                    Rear temperature flap: specified value: 414


-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519)       Labels:. 5Q0-937-08X-V2.clb
   Part No SW: 5Q0 937 084 CQ    HW: 5Q0 937 084 CG
   Component: BCM MQBAB H   H36 0253  
   Serial number: 01001803300303 Dataset Number: V03935274XW 0001
   Coding: 000000000000000000000000000000000000000000000000000000000000
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_BCMMQB 018001
   ROD: EV_BCMBOSCH_018.rod
   VCID: 094F926839BED87278D-805C

   Wiper motor control module: 
   Subsystem 1 - Part No SW: 3V2 955 119     HW: 3V1 955 119   Labels: 5QX-955-119-V1.CLB
   Component: 48x RL 150304  032 0121 
   Serial number: 00000001503020600254
   Coding: 165DDD

   Rain/Light Recognition Sensor: 
   Subsystem 2 - Part No SW: 5Q0 955 547 B    HW: 5Q0 955 547 B  Labels: 5Q0-955-547.CLB
   Component: RLHS  047 0105 
   Serial number: S5Y18M02D06H07M57S53
   Coding: 00084D

   Anti-theft alarm system sensor: 
   Subsystem 3 - Part No SW: 5Q0 951 172     HW: 5Q0 951 172 
   Component: Sensor, DWA  005 0316 
   Serial number: 000000000ZY1734116T7

   Alarm horn: 
   Subsystem 4 - Part No SW: 5QD 951 605     HW: 5QD 951 605 
   Component: Sirene, DWA  005 0314 
   Serial number: 00002856223972902210

No fault code found.

-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J791)       Labels:| 5Q0-919-298.clb
   Part No SW: 5QA 919 298 D    HW: 5QA 919 298 A
   Component: PLA 3.0 12KH07 0050  
   Serial number: 000308417320181 Dataset Number: V03935278BG 0001
   Coding: 0431151851
   Shop #: WSC 12345 123 12345
   ASAM Dataset: EV_EPHVA2CAU3700000 009041
   ROD: EV_EPHVA2CAU3700000_VW41.rod
   VCID: 51FF7A08916EA0B2F0D-8004

No fault code found.

-------------------------------------------------------------------------------
Address 13: Auto Dist. Reg (J428)       Labels:| 3Q0-907-572.clb
   Part No SW: 3Q0 907 572 C    HW: 3Q0 907 572 C
   Component: ACC BOSCH MQB H04 0195  
   Dataset Number: V03935249LS 0001
   Coding: 3200678151FFC428949C8045
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_ACCBOSCHVW48X 001009
   ROD: EV_ACCBOSCHVW48X.rod
   VCID: 35372E9805C6EC92CC5-8060

No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags (J234)       Labels:| 5Q0-959-655.clb
   Part No SW: 5Q0 959 655 BH    HW: 5Q0 959 655 BH
   Component: AirbagVW21    005 0336  
   Serial number: 003VVR3V9FP3 Dataset Number: V03935255BE 0001
   Coding: 98CCC0C0000000005C5400CF00C800000065
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_AirbaVW20SMEVW37X 002158
   ROD: EV_AirbaVW20SMEVW37X_VW37.rod
   VCID: 074B94502FAAAE026E9-8052

   Crash sensor for side airbag: driver side: 
   Subsystem 1 - Part No SW: -----------    HW: 480 003 001 18
   Component: SideSensor_Df  001 0887 
   Serial number: 357000000006E8D42B2W
   Coding: 2D2D2D

   Front Passenger's Side Airbag Crash Sensor: 
   Subsystem 2 - Part No SW: -----------    HW: 480 003 001 18
   Component: SideSensor_Pf  001 0887 
   Serial number: 358000000001E8D42B2S
   Coding: 2D2D2D

   Rear Side Airbag Crash Sensor (on driver's side): 
   Subsystem 3 - Part No SW: -----------    HW: 480 403 101 18
   Component: SideSensor_Dr  000 6149 
   Serial number: 3510001BB28D6142761$
   Coding: 2D2D2D

   Passenger side rear thorax airbag crash sensor: 
   Subsystem 4 - Part No SW: -----------    HW: 480 402 901 18
   Component: SideSensor_Pr  000 6149 
   Serial number: 3520001AD28A2CC366DM
   Coding: 2D2D2D

   Crash sensor for front airbag: driver side: 
   Subsystem 5 - Part No SW: -----------    HW: 480 403 101 18
   Component: FrontSensor_D  000 6149 
   Serial number: 3550001A328C22E512E3
   Coding: 2D2D2D

No fault code found.

-------------------------------------------------------------------------------
Address 16: Steering wheel (J524)       Labels:| 5Q0-953-549.clb
   Part No SW: 5Q0 953 569 C    HW: 5Q0 953 569 C
   Component: Lenks.Modul   100 0265  
   Revision: --------    Serial number: 20230505500383
   Coding: 6014
   Shop #: WSC 01286 386 08256
   ASAM Dataset: EV_SMLSVALEOMQBLRH 001009
   ROD: EV_SMLSVALEOMQBLRH.rod
   VCID: 3E2531B430F02FCA1DF-806A

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments (J285)       Labels:| 5G0-920-XXX-17.clb-SRI3
   Part No SW: 3VD 920 790     HW: 3VD 920 790 
   Component: KOMBI         505 1710  
   Coding: 25A5011A2F80A600018863011001000800000000
   Shop #: WSC 00046 000 00000
   ASAM Dataset: EV_DashBoardVDDMQBA0 001031
   ROD: EV_DashBoardVDDMQBA0_001_VW37.rod
   VCID: 0849976C22B4A17A673-805C

No fault code found.

-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533)       Labels:| 3Q0-907-530-V1.clb
   Part No SW: 3Q0 907 530 L    HW: 3Q0 907 530 C
   Component: GW MQB High   518 5323  
   Serial number: 29011810520042 Dataset Number: V03935276GC 0001
   Coding: 030100045F087300EB00025A1C0F00010001070000000000000000000000
   Shop #: WSC 33361 790 00160
   GVL: 01563C0000000600401C80008002C80000000000000200000000000000000000
   ASAM Dataset: EV_GatewNF 013023
   ROD: EV_GatewNF_VW37.rod
   VCID: 382927AC12D411FAD73-806C

   Generator: 

   Multifunction steering wheel control module: 
   Subsystem 2 - Part No SW: 3V0 919 719 H    HW: 3V0 919 719 H
   Component: E221__MFL-PR6  H03 0180 
   Serial number: 000000000A2948240919

   Battery Monitoring Control Module: 
   Subsystem 3 - Part No SW: 5Q0 915 181 K    HW: 5Q0 915 181 K
   Component: J367-BDMHella  H10 9070 
   Serial number: 1108436404          

No fault code found.

-------------------------------------------------------------------------------
Address 2B: Steer. Col. Lock (J764)       Labels:| 1EA-905-861.clb
   Part No SW: 3Q0 905 861 B    HW: 3Q0 905 861 B
   Component: ELV-MQBB      H05 0020  
   Serial number: 18000007836006
   Coding: 0800000000000000
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_ELVMarqMQBA0 002002
   ROD: EV_ELVMarqMQBA0_SK48.rod
   VCID: 333310800BB2F2A2E21-8066

No fault code found.

-------------------------------------------------------------------------------
Address 36: Seat Mem. Drvr (J810)       Labels:* None
   Part No SW: 5Q0 959 760 C    HW: 5Q0 959 760 C
   Component: Sitzmemory    H09 0024  
   Serial number: Y0006RB426277 Dataset Number: V03935281EC 0001
   Coding: 0014000000000500018280808080000000008181000000D400
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_SeatMemorDriveSide 002022
   ROD: EV_SeatMemorDriveSide.rod
   VCID: 3D2736B83DF634D2045-8068

No fault code found.

-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386)       Labels:| 5QX-959-X93-42.clb
   Part No SW: 5Q4 959 593 E    HW: 5Q4 959 593 B
   Component: TSG FS        011 0032  
   Serial number: 0000302254915  Dataset Number: V03935256LT 0001
   Coding: 001D8020DE01040000001100
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_DCUDriveSideEWMAXCONT 006001
   ROD: EV_DCUDriveSideEWMAXCONT.rod
   VCID: 47CB54506F2A6E02AE9-8012

No fault code found.

-------------------------------------------------------------------------------
Address 44: Steering Assist (J500)       Labels:| 5Q0-909-144.clb
   Part No SW: 5Q0 909 144 AA    HW: 5Q0 909 144 AA
   Component: EPS_MQB_ZFLS  130 1081  
   Dataset Number: V03935273KF 0001
   Coding: 81170000
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_SteerAssisMQB 015157
   ROD: EV_SteerAssisMQB_015.rod
   VCID: 73B3D0804B32B2A2221-8026

No fault code found.

-------------------------------------------------------------------------------
Address 4B: Multifunc. Module (J745)       Labels:| 3Q0-907-338-V1.clb
   Part No SW: 3Q0 907 338     HW: 3Q0 907 338 
   Component: FCM MQB Low   002 0286  
   Serial number: 27011810524395 Dataset Number: V03935274LG 0001
   Coding: 000000020100066E00003F01000000000000000000000000000000000000
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_MultiModulContiVW48X 001010
   ROD: EV_MultiModulContiVW48X_001.rod
   VCID: 72BDD5843428BBAA297-8026

   Left Headlamp Power Output Stage: 
   Subsystem 1 - Part No SW: 8U0 941 329     HW: 8U0 941 329 
   Component: Leimo links  H01 0006 
   Coding: 000000

   Right Headlamp Power Output Stage: 
   Subsystem 2 - Part No SW: 8U0 941 329     HW: 8U0 941 329 
   Component: Leimo rechts  H01 0006 
   Coding: 000000

No fault code found.

-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387)       Labels:| 5QX-959-X92-52.clb
   Part No SW: 5Q4 959 592 E    HW: 5Q4 959 592 B
   Component: TSG BFS       011 0032  
   Serial number: 0000301991938  Dataset Number: V03935256LV 0001
   Coding: 001D0220DE01040000001100
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_DCUPasseSideEWMAXCONT 006001
   ROD: EV_DCUPasseSideEWMAXCONT.rod
   VCID: 46D559546820770A55F-8012

No fault code found.

-------------------------------------------------------------------------------
Address 5F: Information Electr. (J794)       Labels:| 3V0-035-MIB-HGH2.clb
   Part No SW: 565 035 021 B    HW: 565 035 021 
   Component: MU-H-LND-EU   H54 1240  
   Serial number: A853A0JS025626 Dataset Number: V03935271AF 0001
   Coding: 03840101FF00000041111201008808102F0100E601200400DE
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_MUHig4CGen2HBAS 001001
   ROD: EV_MUHig4CGen2HBAS_AU37.rod
   VCID: 0D47A6784DD6C452545-8058

   Display and control head 1 for information electronics: 
   Subsystem 1 - Part No SW: 3V0 919 606 D    HW: 3V0 919 606 D
   Component: ABT_High-2  H50 9130 
   Serial number: SKZ6ZHV0314019      

   Data carrier: 
   Subsystem 2 - Part No SW: V03 959 810 C    HW: -----------
   Component: ECE 2022  --- 0195 
   Serial number: --------------------

   Compact disc data bank: 
   Subsystem 3 - Part No SW: V03 959 800 EG    HW: -----------
   Component: Gracenote2  --- 1017 
   Serial number: --------------------

No fault code found.

-------------------------------------------------------------------------------
Address 6C: Back-up Cam. (J772)       Labels:| 5Q0-980-556.clb
   Part No SW: 5Q0 980 556 B    HW: 4M0 980 556 A
   Component: RVC Compact   H18 0231  
   Dataset Number: V03935257YE 0001
   Coding: 047300010600041F000040
   Shop #: WSC 12345 123 12345
   ASAM Dataset: EV_CamSysRVRVCPANAMQBAB 006009
   ROD: EV_CamSysRVRVCPANAMQBAB.rod
   VCID: 392F22A829DE08F228D-806C

1 Fault Found:
10489856 - No Basic Setting 
          B2010 00 [00001001] - -
          [RearView system not calibrated]
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Priority: 5
                    Fault Frequency: 1
                    Reset counter: 58
                    Mileage: 102997 km
                    Date: 2024.04.29
                    Time: 08:28:33

                    passive


-------------------------------------------------------------------------------
Address 75: Telematics (J949)       Labels:| 5QE-035-285.clb
   Part No SW: 5NA 035 284 B    HW: 5NA 035 284 B
   Component: OCULowMQBLGE  H17 0718  
   Revision: --------    Dataset Number: V03935277FY 0001
   Coding: 03840101EA421A0D3B1C9E000045400382E608
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_OCULowMQBLGE 004044
   ROD: EV_OCULowMQBLGE_004_VW37.rod
   VCID: 3C213BBC26EC3DDA33B-8068

No fault code found.

-------------------------------------------------------------------------------
Address BB: Door Rear Drv (J388)       Labels:* None
   Part No SW: 5Q4 959 595 E    HW: 5Q4 959 595 B
   Component: TSG HFS       012 0032  
   Serial number: 0000302984496  Dataset Number: V03935256MF 0001
   Coding: 001880208001040000001100
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_DCURearDriveMAXCONT 006001
   ROD: EV_DCURearDriveMAXCONT.rod
   VCID: 49CF5268793E9872B8D-801C

No fault code found.

-------------------------------------------------------------------------------
Address BC: Door Rear Pass (J389)       Labels:* None
   Part No SW: 5Q4 959 595 E    HW: 5Q4 959 595 B
   Component: TSG HBFS      012 0032  
   Serial number: 0000302153229  Dataset Number: V03935256ML 0001
   Coding: 001880208001040000001100
   Shop #: WSC 33361 790 00156
   ASAM Dataset: EV_DCURearPasseMAXCONT 006001
   ROD: EV_DCURearPasseMAXCONT.rod
   VCID: 49CF5268793E9872B8D-801C

No fault code found.

End----------(Elapsed Time: 01:36, VBatt start/end: 12.2V/12.2V)-----------

 

I've spotted another version on ebay at the moment - 3V0 907 044 EG which is from a 2017 Superb. It's still a year earlier though and shows an earlier software version (i assume thats what the SW number is) of SW4101. Mine was a 2018 with SW4402. Don't suppose you know if thats likely to work?