No, that is true. I'll let you know how i get on.

Right - Here is a quick update. I fitted this kit 

 

http://www.cars-equipment.com/www/en/shop/park-pilotpla-park-assistentops-sets-parts/oem-front-ops-for-skoda-octavia/ 

 

Connecting it up was fairly simple as I already had rear OPS on a 2012 FL and I had read the other guides. So here are a few pointers

 

1. Change module.

2. Insert front wiring into module. There are 2 wires that go into one of the other plugs. These are well marked on the plug and are on the loom.

3. The rest of the loom is multi plugs that you can't get wrong apart from 2 wires.

4. Brown wire - this goes to a suitable earth.

5. Grey wire (illumination) - this gets connected to the grey / blue stripe wire on one of the other switches. 

 

Then code the module with VCDS. My module came uncoded. VCDS was not very helpful in coding the module.

 

I looked around and found someone elses coding and used that and it worked.

What sensors are people using for rear OPS?

Sent from my Galaxy S5

What sensors are people using for rear OPS?

Sent from my Galaxy S5

4H0 919 275 or 4H0 919 275A

1S0 919 275 or 1S0 919 275A

4H0 919 275 or 4H0 919 275A

1S0 919 275 or 1S0 919 275A

Cheers Eddie

Sent from my Galaxy S5

What are the connections to the PDC button (3TD 919 281) ?

There is the pinouts of this switch?

PIN 1: ???

PIN 2: connect to PDC controller pin 13

PIN 3: ???

PIN 4: ???

PIN 5: connect to PDC controller pin 4

PIN 6: ???

I know that I have to connect the wires to the ESP button, but do not match the colors of the wires and the voltage

 

Picture on this page should help:

http://www.briskoda.net/forums/topic/243174-upgrade-can-gateway-to/#entry2899711

 

Adam

Thanks, but I search the wire connecions of the BUTTON PDC

What are the connections to the PDC button (3TD 919 281) ?

There is the pinouts of this switch?

PIN 1: ???

PIN 2: connect to PDC controller pin 13

PIN 3: ???

PIN 4: ???

PIN 5: connect to PDC controller pin 4

PIN 6: ???

 

Yes that is in the picture. I mean the left hand side of the wiring diagram further down the page...

THANK YOU! It's this:

Today I test it, I hope it is correct ...

I bought the kit to retrofit sensors front for Octavia and have them shipped to me the wires of the button with the different pins!
And they also sent PDC control for Skoda Octavia with code 56D 919 475

I will have problems?

The switch the mk2 Octavia uses is part number 1Z0919281B. The 3t0 part is from the Superb and maybe wired differently.

The correct module is part number 5k0 919 475e I think?

I have the switch 3TD 919 281 there are the pinouts ?

I can wired as the previous image?
I to short circuit something?

Thanks

I don't know if it's the same pin outs for the 3t0 switch sorry. Might be worth asking in the superb section?

IT'S ALL OK !!
I tested the button for superb at my risk with the scheme pins connections.
Fortunately everything went well! Thank you!

interesting reading this and has lead me all over the place with mis information.

 

i have bought the kit to add front ops to my existing rear factory ops.

 

firstly it does need coding despite what anyone tells you and a lengthy search i found the park assist controller needs coding 10001 for the front and rear ops on the screen and 30008 if you have a back up camera and you want it to go auto to that screen with ops down the left hand side.

 

secondly if you have rear ops from the factory you will unplug the front wiring loom from the controller and it will be left there as you need a new loom for the front/rear 8k module.

you can cut the wires in this plug and tap into can high and low here which makes the job 10,000 time easier.

 

i hope this helps anyone in the future.

Hi guys, sending a greetings from Czech Republic.

It is like 1 month I bought Octavia II Facelift, year 2012 equipped by rear parking sensors and radio Bolero. Now I would like to buy parts from destroyed Octavias available on market. It is because the cost is almost 50% lower than completion kit available from new market offers. It is not a problem to get all needed parts however I would like to know the list for what I should be looking for.

 

I expect:

 

- front sensors

- front cables

- button in the interior? (for what purpose?)

 

What else? Is it only about adding parts or should I replaces something as well? If yes, where are parts for exchange located and which numbers should I look for? As the first thing I will check the number of the unit located behind left hand rear wheel.

 

Many thanks in advance. In Czech we have a lot of knowledgable people however they are selfish and not willing to support others without money.

OK, my unit has number 5J0 919 475 A. Not sure whether it needs replacement or not. From all your comments it looks like YES.

From memory, A and B suffix is front only, C is front and rear.

If it has 4k written on it it's rear only

If it has 8k it's for front and rear.

A is rear only I've just removed same module when upgrading

Hello,

Retrofitted PLA 2.0 on my car, all works fine except I do not have 360 OPS on my navigation.

Anyone any ideas?

 

Here are my scans:

 

Address 19: CAN Gateway (J533)       Labels: 7N0-907-530-V2.clb
   Part No SW: 7N0 907 530 AL    HW: 7N0 907 530 AL
   Component: J533  Gateway H58 1642  
   Revision:   H58       Serial number: 110314F1002246
   Coding: 351302
   Shop #: WSC 12345 123 12345
   VCID: 7AE3E5CBACDFA0D251A494D-802E

No fault code found.

 

Address 10: Park/Steer Assist (J791)       Labels: 3AA-919-475.clb
   Part No SW: 3AA 919 475 L    HW: 4H0 919 475 E
   Component: PARKHILFE PLA H06 0025  
   Revision: --------    Serial number: 56261214600036
   Coding: 348001
   Shop #: WSC 12345 123 12345
   ASAM Dataset: EV_EPHVA2C000000000 002008
   ROD: EV_EPHVA2C000000000_SE36.rod
   VCID: 449F5B339E9B26A27BC83A5-8010

No fault code found.

 

Address 56: Radio (J0506)       Labels: 1T0-035-680.clb
   Part No SW: 3T0 035 686 H    HW: 3T0 035 686 H
   Component: RNS-MID       H21 6270  
   Revision: AB001001    Serial number: SKZ6Z7P6022108
   Coding: 0C000402040100800009
   Shop #: WSC 33361 790 00060
   VCID: 3B6D20CFE36559DA0A32591-806E

   Subsystem 1 - Part No: 3T0 051 859 AM
   Component: EU East V13  8350 

 

No fault code found.

 

Address 6C: Back-up Cam.        Labels: 5N0-907-441.clb
   Part No SW: 7N0 907 441     HW: 7N0 907 441
   Component: J772__Rearview      0020  
   Revision: 00H11000    Serial number: 525 PA8J290841
   Coding: 0020011
   Shop #: WSC 98765 666 38384
   VCID: 6ECBD99BE097F072FD2C68D-803A

1 Fault Found:
03006 - Back-up Camera System not calibrated
            000 -  -
             Freeze Frame:
                    Fault Status: 01100000
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 20
                    Time Indication: 0

 

Thank you.

Hello. 

All good now. 360 OPS works, but it will turn on automatically when an obstacle is detected on either side of the car, otherwise it will display only 8 sensors. 

Hi all, 

 

looking for some help ,

I’m wanting to fit front ops pdc kit to my 2012 Octavia. It has rear pdc but I’d like to know where the best place to get a kit including wires and I don’t have access to vcds so would be looking for someone to code it in (Oxfordshire willing to pay) 

 

ive seen this kits but unsure as don’t want cause any faults or issues 

 

also with the wiring side of things I’m normally one for following instructions closely, just don’t want to make a big error.

 

https://www.kufatec.com/en/skoda/octavia/octavia-1z/complete-set-skoda-front-parking-assist-incl.-ops-for-skoda-octavia-1z-39594
 

 

 

On 08/08/2010 at 01:52, ollybroad said:

Here is a wiring diagram I have drawn, apologies, it is a bit rough and ready as it's only for my own use. I will do a full write up when it's complete.

Big Nick, to add the fronts to your existing OPS, you will only have to add the front sensors, speaker and parktronic switch as shown below.

Hi, 

 

I know it's been ten years already. I about to retrofit front parking sensors to my Skoda Octavia mk2 FL and I wonder if you can walk me through the wiring procedures as I dunno what wiring is required. I got the 8K control, front bumper with 4X sensors installed, parking button and connectors.  

 

Thanks!

Osama

On 26/09/2014 at 17:04, KBPhoto said:

I've retro-fitted F&R sensors from a FL Octavia to my pre-FL Octavia and have OPS & PDC; so yes it is.

 

If you already have rear sensors then it involves some wire swapping.

Can you please add some details on what wire swapping do I need when I retrofit only front sensors to a car already has the rear sensors. 

 

Thanks!

On 08/08/2010 at 00:17, ollybroad said:

Good evening thought I’d share my latest triumph. I’ve now wired in and coded my OPS retrofit. I will write a how-to guide once it’s fully finished. I’ve yet to drill the bumper as I wanted to ensure I could get the complete system working before any holes are drilled into the front and rear bumper.

I regretted not going for the rear parking sensors after picking my car up, as it’s not the best visibility out the back. I also liked the display the factory OPS gives you on the Columbus, so decided I would retrofit the OPS and the Park Assist (Self Parking) from the VW Golf. I will do a write up for the Park assist once I have it working next week.

This is the first time i've used VCDS and it is a very good tool, very pleased I brought it.

Front OPS in action

Front and rear OPS in action

OPS unit installed and some of the wiring completed.

Button wired in and installed in dash

Mounting one of the speakers on the B pillar

Finally found the CAN Gateway. This is on the driver side on the FL not behind the glovebox as I believe it may be on other models/years.

I wonder where to mount the speaker for front sensors?