Skip to content

D.FYLAKTOS

FREEDOMLite
  • Joined

  • Last visited

Everything posted by D.FYLAKTOS

  1. That's the 2nd and the 5th solution but what's going to happen with the rain-car wash water drops which will inevitably fall inside? I am concern about the time that the ''natural dry'' will take. The plastic scuttle in Felicia does not provide air, it's away from the cabin filter (in Octavia 1U it covers it) https://www.briskoda.net/forums/uploads/monthly_11_2016/post-132001-0-03211800-1479035440.jpg beneath are the drain grooves which must be take care of from leaves and other dirt, we clean them with compressed air.
  2. There is almost 2 cm empty space and the result is that odours from the engine pass through the sponge into the cabin. Why that space must exist? Wouldn't be better if i ''seal'' the whole system? Think in the other car of yours, the pollen filter draws air from the engine bay as the Felicia does?
  3. Gentlemen, I thought more about how to convert the existing cabin air filter system because the years have passed, i am not young and careless about health issues like before and allergies are getting worse in the environment we live in. This is the existing (factory) system that I have, from its grille air blows in and from below I have a sponge made of activated carbon, while below I added a layer of kitchen filter absorber to hold more particles and to better close the gaps on the sides. The metal lip of the hood does NOT seal well, it is smaller in size than the sponge and does not touch it, so there is almost 2 cm empty space and the result is that odours from the engine pass through the sponge into the cabin. I remind you that rain drops and also water from the car wash to some extent fall on the sponge, which however, dries out through the heat of the environment and from the heat of the engine. Intermediate solution: I put a piece of stainless steel mesh to hold leaf-insects but all the above still apply. 1st solution: I go to a 3D printer, they make a "hat" for me, i.e. a rectangular parallelogram on top i fit a Filtron pollen filter for Skoda Felicia 1600 and an oval on the bottom to rest on the existing plastic frame. Yes, the air will be filtered better by the sponge, but there is still the issue of the odours from the engine room hitting the pollen filter. 2nd solution: Once again, I make a plastic frame with a 3D printer, I glue it back and as it comes down, it completely "closes" the lower structure, completely sealing it as we say: the cabin will only get air from the environment but there is the issue of drying since the engine air will not catch it and I have to wait in a "natural way" for example the sun to dry the Filtron pollen filter. 3rd solution: Again, I make a plastic frame with a 3D printer, I glue it back and as it goes down, it reaches evenly, it will barely touches the bottom construction, so: the cabin will get enough air from the environment and a little bit from the engine, while the Filtron dust filter will dry a little naturally, but also at bit from the hot air of the engine. 4th solution: Using a 3D printer, I make a plastic frame, glue it back and as it goes down, i bring it level with the surface barely touches the construction below, so: the cabin will get enough air from the environment, the screen will keep the leaves-flyers but there will be a minimal space where the heat of the engine room will dry the fine filter which will be made of an kitchen absorbent filter. 5th solution: With a 3D printer, I make a plastic frame, I glue it back and as it goes down, it completely "closes" the lower structure, completely sealing which will only consist of an absorber filter, so: the cabin will only take in air from the environment and the kitchen absorbent filter will dry faster in a natural way, for example the sun, since it will be thinner. @Papez @Thefeliciahacker @Raychev05 @Breezy_Pete @DeanVRS20VT or any other fine Gentleman who wants to help me i would love to hear your opinions.
  4. Felicia 1.3 has no pollen filter from the factory, just this charcoal sponge. The plastic scuttle cover is fine and far away from the sponge, the drain holes are OK too. The fresh air (plus water drops) are coming from the hood grille which is above that metalllic lip. We just talking trying to help each other as Human being.
  5. Yes but remember Felicia from factory has this The upper oval shape metallic lip (which brings fresh air into the cabin) is narrower than the sponge and does not seal properly plus the sponge let some dirt to pass from the sides. For years i make complains that i have some odour (like burned coolant for example) inside the cabin. A pollen filter (fitted with patent which would seal properly with he upper metallic lip) couldn't make things better that now?
  6. My dilemma is: should i make the upper metal lip (of the hood) to touch on top of the pollen filter or should it have a gap to circulate the air of the engine room? In the 1st case it will get mostly fresh air but it will be more difficult to dry and smell like mold will come to the cabin. In the 2nd case, it will dry more easily, but air with smells will pass with from the engine room to the cabin. Gentlemen, what you suggest?
  7. https://www.briskoda.net/forums/topic/422277-water-coming-in-though-pollen-filter/ I have also read this but my question is how fast a wet pollen filter (exposed as i want to put) can get dry?
  8. In mine, water (rain-car washing) falls onto the charcoal sponge and i wonder if i place in it's position a cabin filter will get dry easily or not? The diversion of the water is small.
  9. Here was my previous used ECU. The ECU is not a ''plug and play'' item, the programmer must make too many adjustments after fitting (among them is the immobilizer) fuel ratio etc plus a test on Dyno-road. Yes the programmer can do it but this will turn the car back to previous decades which anyone could start the engine easily. It's a Safety feature.
  10. That's a mistake, you can not know what problem that ECU has (burned, slight damaged, overpowered, moisture, pin corrosion etc). Only a programmer must buy it since will get a six months warranty plus will make the fitting-adjustments etc. I have lived that nightmare in the past, cheap used ECU bought by distance = trap. Hall sensor you mean the Crank sensor, did you check beneath of it if there is an empty space on the flywheel? Tomorrow i will post a photo from the pins of ECU,now it's late and i am on cellphone.
  11. So from where gets only fresh air? From the grille of the hood among air for sure will pass some water and yes will drain through holes but even in surface the filter wouldn't get wet even a liitle bit and temporary?
  12. Mine is 45mm (outside) We measure internal or external?
  13. Fellow Skodians, i see in the below video where the pollen filter is (well, the fact that the leaves fell in again and the filter was inserted from above is ridiculous) in the Octavia 1U and I have the following question: Where it is, doesn't it get wet at once from rain and car washing? How does it dry? do you wait in a natural way, for example sun or a warm engine bay? When it's soaked, don't you breathe moist air? Isn't it "unhealthy" let's put it that way plus foggy windows? I want to make a modification in my car (Felicia) and based on this i have thought of something similar (pollen filter beneath the hood grille) but immediately i had this question. A pollen filter that is exposed like this, let's say, how long does it last before changing?
  14. Gentlemen, i have in my Felicia those Tecnomagnesio 14" wheels with 175-60 tyres : From the side look like this: Unfortunately the spokes are prone to scratches in the pavement because i park the car in the street every night almost with not enough space from the concrete, things are not comfortable especially if other cars are behind you waiting so it's very easy to make a scratch to the spots that i am showing with arrows because they stand out a bit. If a let big space between the car and the pavement there is a risk for a truck to scratch my doors or hit the wheels, the roads here are not like USA country and every night i struggle to find a space to park properly. It's already time to paint them (no cracks and never crashed them) but soon or latter the scratches will show-up so my thought is to give them for a modification so they will look like these: The mechanic will cut and weld the 6 spokes a bit inside so there would be a gap between the spokes and the rims. I can protect the outside of the wheel with a stripe which are made for this cause and the spokes can not be scratched while parking but: 1) Is it safe? Yes the guy which make the project is the most famous here in Greece with a repair-shop dedicated to wheels but i still feel that i have to ask other drivers first 2) there would be an Offset change? This will make the car turn in different way that i have use to drive? New wheels means: 145 euro per unit plus installing = at least 620 euro so forget a new purchase.
  15. Sorry i saw this too late. Have you checked the wires-plugs at the rear? Sometimes they unpluged a bit-corrosion etc.
  16. I saw your first post in my smartphone while i was at work, i went to a corner so i wasn't visible from the camera, wear my vision glasses and as i was standing upright tryied to write a quick post to help you although english are not my first language. I have the same car with you but i can't do anything more, i am sure other members will help you to solve your problem.
  17. https://check-vehicle-compatibility-e10-petrol.service.gov.uk/manufacturer/Škoda We are not prophets or magicians and this is not a Court of Law with he ''ask the question" rule to the examined witness.
  18. Why you spend money changing things without reason? Many of us have done this in the past and it was wrong...very wrong. Have you check the vacuum hose? Your mechanic check the fuel pressure regulator? The spark plugs are ok? Your throttle is clean? The VCDS shown any errors?
  19. Check my posts, you will find photos of damaged cables from my coolant sensor, mine has Blue ring. Check your spark plugs. Cleaning the injectors and checking the fuel pressure regulator is a "must" since the car wasn't maintenend. @Thefeliciahacker had a similar problem with you, has a thread for this with videos.
  20. I have a 1.3 GLX made at late 1999 months and bought it at 2000. Those days you could find Eibach anti-roll bar in the market, now the stopped produce it https://www.eibach-shop.com/skoda-c-85510.html no modifications, fitted as it should be. The strut brace was bought from the local Skoda dealer (original accessoire). You may lose some comfort but if you are a sport driving guy that combination will help you a lot, if you start diving fast in mountain road without them the car will start floundering like a boat in a heavy sea. After some turns you will start feeling fear and unsecure so you will start slow down.

Account

Navigation

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.