13 hours ago, JR RS said:

 

The Superb doesn't have the sound generator.

Are you sure? My iV has a fake engine noise when it's running on battery only...ive also read that it can be adjusted 

iV indeed has a sound generator, because it is a hybrid.

If I remember correctly there is a legal requirement for electric cars to have sound generator. Also electric Citigo should have it. I can confirm that eUp has it and is really annoying, because it has poor sound insulation.

2 hours ago, techsearchuk said:

Are you sure? My iV has a fake engine noise when it's running on battery only...ive also read that it can be adjusted 

 

Sorry, I was referring to the pre-facelift Superbs.

I have just bought a facelift Superb 3 SE tech which has ACC and what looks like the camera in the windscreen.

 

I like to know how I can enable Lane assist which is not an option in the settings.

 

 

There is a thread which lists members who have VCDS interfaces, which will allow changes to be made to the system in your car. There is also a handy map on the thread that will allow you to find members close to you.

 

I was able to successfully contact a local member, and yesterday successfully enabled TSA, amongst a few other smaller tweaks. Throttle response, rear lights on when DRL are on, disable boot close warning chime, off-road screen etc.

On 07/05/2021 at 22:58, stubie141258 said:

I have just bought a facelift Superb 3 SE tech which has ACC and what looks like the camera in the windscreen.

 

I like to know how I can enable Lane assist which is not an option in the settings.

 

 

maybe this might give you some ideas to try 

I'm aware the mod for 30 colour pallet in the ambient lighting screen has been mentioned several times on the forum.

TLDR: The RGB values used on available in the table at the bottom on my post.

 

There was some rough guidance on RGB values, but  I wanted to aim for an OEM+ look. 

I've taken some time build a colour pallet of 30 colours based on the original 10 that come as standard.

Rather than attempting to join up the dots by looking at raw RGB values, I've built a gradient for the 10 RGB values from the originals. I then referenced 30 colours from the gradient and noted down the values.

 

Below is the original screen values, the gradient, and the 30 colours picked out.

 

 

The ambient lighting strip uses different colours values to the screen values, interesting though, the white value from the ambient light strip is actually a light green, but appears white on the strip.

 

 

The original pallet prior to coding:

 

The 30 colour pallet after coding.

 

A massive thanks for @Ivan8192 for helping with the script, and allowing access to his VCDS again!  and to @SashaGracefor piquing my interest into this mod.

 

For anyone interested the RGB values are available below:

 

 

Screen				Ambient Strip
Basic Colour	Red	Green	Blue	Basic Colour	Red	Green	Blue
White	217	221	233	White	120	231	71
	229	205	161		163	221	49
	241	190	88		205	211	26
Yellow	253	174	16	Yellow	247	202	4
	254	155	18		234	167	2
	254	135	34		208	128	3
Orange	253	115	50	Orange	183	89	5
	251	85	52		189	60	5
	247	51	47		215	40	4
Red	244	18	43	Red	241	20	3
	244	19	73		255	27	17
	247	59	142		255	65	49
Lilac	251	100	212	Lilac	255	105	82
	232	109	243		244	134	112
	197	98	247		196	136	136
Magenta	163	86	251	Magenta	149	138	160
	129	77	255		104	139	183
	87	85	255		70	130	207
Blue	45	93	255	Blue	37	121	229
	5	101	255		4	111	251
	0	127	255		8	142	226
Cyan	1	156	255	Cyan	17	179	194
	1	184	255		26	215	162
	1	194	214		35	229	120
Green	0	197	157	Green	45	236	73
	0	200	99		54	242	27
	30	210	70		58	228	3
Lemon	88	227	65	Lemon	58	196	2
	145	244	60		57	163	1
	182	255	57		57	132	0

Interesting! Nice job!

Could you remind the "spte-by-step" process, to "add" the 20 other colors please?

Thanks!

1 hour ago, Bap33 said:

Interesting! Nice job!

Could you remind the "spte-by-step" process, to "add" the 20 other colors please?

Thanks!

 

@Bap33 Here is the script I created for using with VCDScripter, containing the RGB values from @Hdsn555. It is pretty self-explanatory. You can manually set the values using VCDS but I didn't fancy  doing it manually so used VCDScripter. Your car is only showing colours 1-10 at the moment because the 11-30 RGB values are all zero by default. Once you start changing these, you will get more colours. I think it needed the car to be switched off for say, 10 seconds, then back on again, for it to start showing more colours in the Settings page, once the changes were made.

30colours_v2.txt

Just to add to @Ivan8192 post, if you have 'auto' ambient lighting modes where it changes colour based on driving mode, you should also check and update the "Ambientelicht Zuordnung der Farbe zum Fahrprofil-Fahrprofil" adaption channels too

 

Other than that, you might need to set a WSC and importer and equipment number on this screen if you haven't already.

@langers2k Thanks for the info. No, I've not set the auto driving mode colour changes, I had seen the 0-15 settings in the admap, but hadn't looked at them any further. Something else to play with 

This thread is turned into a bit of a Behemoth, but it does appear there are some tried and tested VCDS changes that aren't captured in the 'Superb MKIII VCDS Adaptations - tried and tested - Diagnostics & VCDS - BRISKODA' thread which is locked.

Not sure if @Gizmo is still actively moderating, as I'm pretty new here, but might be worth capturing some of the mods in this and updating the tried and test thread, as it was last updated November '19?

 

 

1 hour ago, Hdsn555 said:

This thread is turned into a bit of a Behemoth, but it does appear there are some tried and tested VCDS changes that aren't captured in the 'Superb MKIII VCDS Adaptations - tried and tested - Diagnostics & VCDS - BRISKODA' thread which is locked.

Not sure if @Gizmo is still actively moderating, as I'm pretty new here, but might be worth capturing some of the mods in this and updating the tried and test thread, as it was last updated November '19?

 

 

Indeed, I had sent a PM several months ago to add 1 or 2 mods I had found to this 'tried & tested' thread, but no answer... 

Edited 24 May, 20215 yr by Bap33

On 22/05/2021 at 10:26, langers2k said:

Just to add to @Ivan8192 post, if you have 'auto' ambient lighting modes where it changes colour based on driving mode, you should also check and update the "Ambientelicht Zuordnung der Farbe zum Fahrprofil-Fahrprofil" adaption channels too

 

Other than that, you might need to set a WSC and importer and equipment number on this screen if you haven't already.

Just to expand on this, for each driving profile, you set the colour to a number from 1-30 which represent the 30 colours left to right on your display

 

leaving/coming home (I set mine to a warm amber '6')

ENG153712-ENG154602-Ambientelicht Zuordnung der Farbe zum Fahrprofil-Fahrprofil_0

 

eco (I set it green 28)
ENG153712-ENG154603-Ambientelicht Zuordnung der Farbe zum Fahrprofil-Fahrprofil_1

 

normal (I set it offwhite 3 to be the calmest on the eyes, and also to provide the best wow factor when passengers don't realise you have colour lighting other than white until you shift to another driving mode)
ENG153712-ENG154610-Ambientelicht Zuordnung der Farbe zum Fahrprofil-Fahrprofil_2

 

sport (I set it to 10 - red - of course!)

ENG153712-ENG154611-Ambientelicht Zuordnung der Farbe zum Fahrprofil-Fahrprofil_3

 

I've attached v3 of the script, including these driving profiles, if you don't want driving profiles, then use v2. if you've already done the script v2, and you just want to add the driving profiles, I've attached a script to just add the driving profile colours on their own
 

30colours_just_driving_profiles.txt 30colours_v3_with_driving_profiles.txt

Few other profiles, not all will be applicable to your car:

• 0 - Doors open (coming/leaving home)
• 1 - Comfort
• 2 - Normal
• 3 - Sport
• 4 - Off-road (?)
• 5 - Eco
• 6 - Race/Cupra (?)
• 7 - Individual
• 10 - Snow (?)
• 11 - Individual off-road (?)

Question marks on modes I haven't got so I can't confirm

26 minutes ago, langers2k said:

Few other profiles, not all will be applicable to your car:

• 0 - Doors open (coming/leaving home)
• 1 - Comfort
• 2 - Normal
• 3 - Sport
• 4 - Off-road (?)
• 5 - Eco
• 6 - Race/Cupra (?)
• 7 - Individual
• 10 - Snow (?)
• 11 - Individual off-road (?)

Question marks on modes I haven't got so I can't confirm

I wonder if its possible to add these modes to a car which only normally has 4, for instance i have added the offroad display ability to the mib2, but i wonder if it can be added as a new mode

I think adding modes is hard as you'll need the correct FeC to enable it

 

new versions attached, amended to reflect some corrections to driving mode numbers as kindly provided by @langers2k, and to include comfort mode which I missed

 

30colours_v4_with_driving_profiles.txt 30colours_just_driving_profiles_v2.txt

Edited 28 May, 20215 yr by AlVal

6 hours ago, AlVal said:

new versions attached, amended to reflect some corrections to driving mode numbers as kindly provided by @langers2k, and to include comfort mode which I missed

 

30colours_v4_with_driving_profiles.txt 18.02 kB · 1 download 30colours_just_driving_profiles_v2.txt 722 B · 0 downloads

Which 30 colour pallet did you use?

On 20/05/2021 at 21:34, MICKSVRS said:

 

 

10 hours ago, Hdsn555 said:

Which 30 colour pallet did you use?

The latest one provided by Ivan above

Edited 29 May, 20215 yr by AlVal

Is there a thread for OBDEleven as well?

I'm going to write a description of how to get 30 colours with OBD11 once I've entered the correct numbers for the LED-strip

(the description I was working with didn't take into account that the values need to be different from the screen values, most of the LED strip colours got very pale and strange  )

3 minutes ago, Riolux said:

Is there a thread for OBDEleven as well?

I'm going to write a description of how to get 30 colours with OBD11 once I've entered the correct numbers for the LED-strip

(the description I was working with didn't take into account that the values need to be different from the screen values, most of the LED strip colours got very pale and strange  )

If you use the colour values I posted above in the table, you'll find they should match the screen colour very well, feels pretty OEM too!

1 minute ago, Hdsn555 said:

If you use the colour values I posted above in the table, you'll find they should match the screen colour very well, feels pretty OEM too!

 

Yes, this was very helpful. Thank you!

 

Yesterday I thought I had failed, but then I remembered seeing your picture:

 

 

I also noticed some differences in the screen values, your list makes it look more OEM than the list I used yesterday.

4 minutes ago, Riolux said:

 

Yes, this was very helpful. Thank you!

 

Yesterday I thought I had failed, but then I remembered seeing your picture:

 

 

I also noticed some differences in the screen values, your list makes it look more OEM than the list I used yesterday.

Strange how the LED strip isn't RGB, with the green value appearing on the far left appearing white on the strip.

 

There are quite a few RGB values floating around I think, but I wanted to go for an OEM feel. Once I'd got the stock values, I then mapped the 30, for both screen & strip. Currently using a teal green at the moment, but rarely drive it at night so don't get chance to appreciate the handy work!

Is it possible to disable "cabin air recirculation auto off" via vcds?  If the outside temperature below 5 C   it shuts off randomly,  sometimes it shuts off in an area with bad smell and it is too late when i realize that it shut off.

Or can this 5 C threshold be changed? for example to 0 C??