All Activity

I haven't found a way of switching off the speed limit warning permanently, I have to switch it off every time I restart the car. Ditto for Lane Assist.

If the car has build code 1KE, then search for any of the five below OEM part numbers. Build code 1KE is an ATE brake system. Brake pads for 272x10mm rear brake discs (build code 1KE) 5WA698451 5WA698451E 5WA698451G 8Y0698451 8Y0698451C https://www.autodoc.co.uk/car-parts/oem/5wa698451?supplier%5B%5D=833&supplier%5B%5D=62&supplier%5B%5D=48&supplier%5B%5D=3

I've had a few AGM batteries on my MX5 and they've not lasted well at all, failing quite quickly due to cold weather and, or low charge. I've therefore moved back to EFB and they've been far more reliable - I won't be buying AGM again unless I absolutely have to as they are too fagile IMHO.

Tbh I'm starting to leaning towards getting the Bosch AGM, hopefully should only cost about €200 then hopefully I should be able to code it myself with OBDEleven.

@Kojne I've got a 2021 Octavia, and similar to others on the forum had endless software issues. They're all sorted now, but it was a pain getting them resolved. The local dealer was good, but they had issues with Skoda technical. As others have mentioned the infotainment being up to date is important. But it would also be worth asking if components such as the OCU are up to date. You cannot check the version of that from within the car. I believe the current OCU version is 0311. My car had several updates to components such as this to resolve all the issues. Components like the OCU you cannot update yourself, so much better to get a dealer to do it for you. It's also worth noting that some of the earlier cars are unable to download 'big' updates over the air. My car has never been able to receive infotainment and OCU updates OTA where others have. I would definitely check on the OCU version.

IMHO definitely yes.

By doing a scan with OBDeleven or VCDS.

On autodoc, 1T0413031FK isn't listed against the Bilstein 22-183729 front shock absorber but 1T0413031HL is listed against Bilstein 22-183729. Sachs and KYB list 1T0413031FK and 1T0413031HL against the same aftermarket shock absorber, so these two shock absorbers do appear to be interchangeable. Bilstein lists the 22-183729 front shock absorber against both standard ride height and increased ride height OEM part numbers. It may be just an oversight on Bilstein's part that they haven't listed 1T0413031FK against their 22-183729. OEM part number for front shock absorbers (Octavia MK2 estate 4x4 with increased ride height) (55mm strut diameter) 1T0413031FK (up to the 2008 model year) 1T0413031HL (from the 2009 model year)

Hi all - I've had this issue a while, and with the wintry weather upon us I figured it best to get fixed (I figured being able to see while driving through torrential rain is kind of a big deal...) Wipers work fine on intermittent mode, and at regular speed, but when pushed to the top maximum speed, they just drag really slowly like the power isn't there to make them work. Has anyone had a similar issue and found a fix? Google suggests a new wiper motor is needed, which makes sense to me on an 11-year-old car (one of the annoying things that starts to drop off a bit). TIA

Hi what rear pad do I need for me skoda octavia mk4.5 facelift 2024 1.5 tsi. Thanks

^^^ Exactly. Even with Skoda dealerships, some used to give you a FREE Change of oil. or a voucher to come in after 1,000 miles and have an Oil & Filter change and an inspection. I have not seen any doing that since about 2012 when SERVICE BOOKS stopped being put in the car at Hand Over. People might well want to change oil in cars earlier than annually, but as the first oil change. That is good oil filled at the factory. It has a job to do and IMO best leave it doing that job. Check the oil regularly though. From getting the new car home. Know where the oil is at Stone cold and compare to where when checked as per the Manufacturers guidelines/ @ Normal Operating temperature after a few minutes parked on the flat.

Hello, I'm on MST2_EU_SK_ZR_P0245T with GEM3.5 and want to activate carplay via toolbox, but i can't figure out, if i need to/should upgrade the firmware first. If that is the case, i would like the 480 version.

I used https://youtu.be/4I5Lnwc1w5c?is=dtFPT81Ak71vbc4n

Thank you for your help and comments.

Never had a new car but friends have. A few dealers like mitsubishi etc change oil and filter at around 1000-2500 miles on brand new cars then revert to standard service intervals. Not sure about Skoda. Something to do with a run in period to remove any debris etc from new engine . Alasdair

I am tempted to use VW 504 when my brand new Karoq (sept 2026 manufactured) reaches 5000km, as I have 16L left in the dunk from my last Fabia change (I buy dunks of 20L VW 504 for changing to Fabia every 8000km). My worry is that there is void guarantee risk since if something happens to the car they may be for sure a process to check that does not have VW 508 oil in? The oil filter will replace exactly the original one.

For the non-maxidot version, I'm pretty sure it's: 03 - byte 16, bit 2 17 - byte 2, bit 0 There will be no 4C module and the reset can either be done with VCDS or a physical switch.

I may be wrong but read that if an auto ecu is used it looks for live data from auto box. As yours is a manual it sounds like its dropping into limp mode when it doesnt recieve it. I found this on AI which I generally dont trust but it makes a bit of sense. Well above my expertise level though. The security login to ecu may help?? On the Skoda Fabia Mk1 1.4 (Magneti Marelli 4LV / 4MV ECU), you cannot simply recode an automatic engine ECU to manual via standard software coding (like VCDS / VAG-COM). The ECU software is flash-locked by the factory specifically to the transmission type it was built for, causing it to reject manual transmission coding strings natively. [1, 2, 3] To fix this and stop the ECU from looking for the missing Transmission Control Module (TCM), choose one of the following paths: 1. Flash the ECU Firmware (EEPROM/Flash Edit) The factory automatic dataset does not contain the manual maps/blocks. To override this, a chiptuning or ECU cloning specialist must read the ECU on a bench using a bootloader or OBD tool (such as FoxFlash or KESS) and write a full flash and EEPROM backup file from a factory manual car with the exact same engine code (e.g., AUA, BBY, BBZ). [1, 2, 3] Note: Reflashing the ECU will alter the internal immobilizer data, meaning you will also need an Immobilizer Off (Immo Off) patch or to manually adapt the keys/cluster. [1, 2] 2. Swap to a Factory Manual ECU The simplest physical workaround is to source a used Magneti Marelli ECU pulled directly from a donor manual car. Ensure the VAG part number matches your engine variant. You will need to extract the PIN code from the replacement ECU to align it to your instrument cluster and keys, or have it delivered with the immobilizer disabled. [1, 2, 3] 3. Check the CAN Gateway & Interlocking Modules If you have already altered the ECU code at a hardware level but your coding is still rejected, other modules are likely blocking the change. VAG ECUs look at the CAN Gateway during coding verification. [1] Recode Module 19 (CAN Gateway): Open the CAN Gateway profile, look at the installation list, and uncheck/remove the Automatic Transmission (Module 02). Clear Fault Codes First: The ECU will refuse a coding adaptation if active "No Communication with TCM" codes are locked into other systems. Erase fault codes completely in ABS (03) and Instruments (17) before attempting to change the engine coding. [1, 2] Login Code Requirement: Some Marelli 4LV units require a security login string (such as 01283 or 11463) under Login - 11 before they unlock the Coding - 07 permission window. [1, 2] Alasdair

I've taken to just replacing the rubbers in the wipers because I cannot find the right ones. I've tried Bosch and other brands but none of the fittings work on the Enyak. It is supposed to be one of the UK's best selling EVs, so you would have hoped that someone will have made wipers that fit!

Currently there are five UK-marketed Fabia Mk4 models SE Edition Design Edition SE L Edition Monte Carlo Edition 130 and (assuming Skoda's data on the online Standard Equipment data are correct) SE Edition and Design Edition models do NOT have the "Hill Hold Control" (HHC) driver assistance feature, whereas SE L Edition, Monte Carlo Edition and 130 models do have it. HHC is mentioned in the Driver Assist systems/Braking and stabilising systems/Overview section of my late-2023-built Fabia SE L model's online Owner's Manual (and in later Fabia Mk4 Manuals) Hill Hold Control (HHC) The HHC system helps with hill starts by braking the vehicle for approximately 2 seconds after the brake pedal is released. Operating conditions The gradient is at least 5 %. The driver's door is closed. I don't know if my car actually has the HHC assist feature and - as my Fabia has DSG transmission and my two working feet can simultaneously operate its two foot-pedals - I've no real need for HHC. My last motorhome (Fiat-Ducato-based, left-hand-drive, 3500kg weight with manual transmission and a handbrake designed for people with a long left am and gorilla muscles) had a hill-hold system and that was really helpful starting from rest on a steep hill. There is some discussion on the OBDeleven forum about activating HHC on Fabia Mk4 cars that do not have HHC as part of its standard specification. I don't know if it can be done on your 2025 car, but you could explore that possibility if you really like the idea of having HHC.

On hot ambient temperature misfires are more than in cold mornings. For example 2 days before i had 129 misfires on cylinder 4 for 1000 rpm on idle speed. On next day with same conditions i had no misfires. What can be the issue, any temperature sensor, trottle valve?

Good morning, Thank you so much for the above I will start ordering parts 😁. Can I ask did you change to the alloy hubs etc and if so any best practice? I can see that the wheel bearing mounts different and the caliper may need some work but unsure. I figure if I am in there I may as well do everything at the same time subframe, wishbones, ARB, Shocks springs and hubs. Might do the rear bits whilst I am there also what do you think?

Hi Derek. This is the display i have (digital cockpit) also no hill start assist with this model.

Wheel is on left side, correct, not UK. Not all cars are involved. Some of them which have bolts of some series. VAG dont produce these bolts. Original bolts are made in some steelworks in India. Different factories, different versions, some of them were low quality. Same bolts are used on other parts of suspension, engine mounts, etc.

You may have recalled an earlier part of the conversation where I mentioned about an ongoing issues with the ECU (marriage), what I forgot to mention is this: On quite a number of occasions whilst driving and attempting to squeeze some engine revs, the computer would not allow me to rev pass 3000 rpm, it would slap the rev counter back to 0 and when I attempted to try to maintain that figure, it would kill the rev counter all together, strange behaviour that. I would have to switch off the car and allow things to reset. I Mentioned this because you had said that the immobilizer data was copied etc etc, I'm thinking with firmness that the marriage is not rock solid, it's so bad that the car idles weak, runs very rich which in turn us fouling my spark plugs amongst many other performance /normalcy issues,so I'm starting with the ECU kit, if the flash is more attainable that would be even more awesome, we shall see